Main Drive Shaft - Install
Note: Cleanliness is an important factor. Before the installation procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Attach a suitable lifting device to main drive shaft (17). Use two people in order to install main drive shaft (17) into the machine. The weight of main drive shaft (17) is approximately
38 kg (83 lb) . - Align the keyways and install bolts (19) in order to connect main drive shaft (17) to the output transfer gears. Tighten bolts (19) to a torque of
135 ± 20 N·m (100 ± 15 lb ft) .Show/hide tableIllustration 2 g01202807 - Align the keyways and install bolts (18) in order to connect main drive shaft (17) to the transmission. Tighten the bolts to a torque of
135 ± 20 N·m (100 ± 15 lb ft) .Show/hide tableIllustration 3 g01202809 Show/hide tableIllustration 4 g01202820 - Install tube assembly (15). Tighten clamp (16) and clamp (14).
Show/hide table
Illustration 5 g01202815 - Install tube assembly (13). Install hose assembly (12).
Show/hide table
Illustration 6 g01202804 - Install tube (11), tube (10), and tube (9). Tighten clamps (8), clamps (7), and clamp (6).
Show/hide table
Illustration 7 g01202812 - Tighten clamp (5). Install clamp (4). Tighten clamp (3). Install clamp (2). Tighten clamp (1).
- Remove the steering frame locks. Refer to Operation and Maintenance Manual, "Steering Frame Lock".
Show/hide table
Illustration 1 | g01202818 |
End By:
- Install the cab. Refer to Disassembly and Assembly, "Cab - Install".
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
AP-1055D and BG-2455D Asphalt Pavers Propel System Piston Pump Flow - Test - Steel Track
AP-1055D and BG-2455D Asphalt Pavers Propel System Piston Pump Neutral - Test and Adjust - Steel Track
AP-1055D and BG-2455D Asphalt Pavers Propel System Pressure Limiter Valve - Test and Adjust - Steel Track
AP-1055D and BG-2455D Asphalt Pavers Propel System Relief Valve (Charge) - Test and Adjust - Steel Track
AP-1055D and BG-2455D Asphalt Pavers Propel System Relief Valve (Track Tension) - Test and Adjust - Steel Track
AP-1055D and BG-2455D Asphalt Pavers Propel System Seal Leakage (Brake Piston) - Test
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Truck Body - Remove
414E, 416E, 420E and 430E Backhoe Loaders Axles, Differential and Brakes Differential Lock - If Equipped
793D Off-Highway Truck Air System and Brakes Diverter Valve (Front Brake Cooling)
AP-1000D and BG-260D Asphalt Pavers Operation Information
2005/11/28 The 6V-8633 Connector Has Changed {5057, 7553}
C27 and C32 Engines for Caterpillar Built Machines Poor Acceleration or Response
2005/09/12 The Routing for the Breather Hose Has Changed {1317}
C11 and C15 Engines for Caterpillar Built Machines System Overview
793D Off-Highway Truck Power Train Final Drive
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 0681 - FMI 03
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 0681 - FMI 05
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 0681 - FMI 06
3176C Engines for Caterpillar Built Machines CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
AccuGrade® Laser (CB420) MID 114 - CID 2262 - FMI 07
AP-1000D and BG-260D Asphalt Pavers Engine Starting
C11 and C13 Engines Exhaust Manifold
725, 730 and 730 EJECTOR Articulated Trucks Power Train Main Drive Shaft - Remove