Final Drive (Drive and Steering Axle)(Front) - Disassemble - In Chassis
Disassembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-8757     | Spanner Wrench As     | 1     |
Start By:
- Remove the front tires. Refer to Disassembly and Assembly, "Tire and Rim (Front) - Remove and Install".
- Remove the cotter pin and the nut from tie rod (1) .
Show/hide table
Illustration 1 | g01082173 |
- Install a suitable full nut in order to separate the tie rod from the steering knuckle. Remove the full nut.
- Disconnect tie rod (1) .
- Remove plug (4) in order to drain the final drive fluid into a suitable container.
- Remove screws (2) .
- Remove carrier assembly (3) .
- Remove retaining rings (5), rings (6) and (9), gears (7), and bearings (8) from carrier assembly (3) .
Show/hide table
Illustration 2 | g01090518 |
- Remove sun gear (25), retaining ring (27), and thrust washers (28), and (29) .
Show/hide table
Illustration 3 | g01082147 |
- Remove screw (24) and lock plate (23) .
- Use Tooling (A) in order to remove nut (30), gear (22), and bearing cone (21) .
- Remove O-ring seal (31) .
- Remove hub assembly (26) .
- Remove bearing cups (20) and (19) from hub assembly (26) .
- Remove seal (14) and bearing cone (18) .
- Remove bolts (10), ball joint (11), shim (12), O-ring seal (13), bearing cap (16), and bearing cone (17) .
- Repeat Step 15 for the bottom.
- Remove housing (15) .
- Remove bearing cup (32). Repeat for the bottom.
Show/hide table
Illustration 4 | g01082203 |
- Remove U-joint (37) .
- Remove clip (38) and bushing (39) from U-joint (37) .
- Remove clip (36) and bushing (35) from U-joint (37) .
- Remove shaft (34) and seal (33) .
Caterpillar Information System:
2004/08/02 New Proportional Control Handle Is Now Available {5705}
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Remove
446D Backhoe Loader Engine Supplement Hydraulic Oil Cooler - Remove and Install
446D Backhoe Loader Power Train Drive and Steering Axle (Front) - Install
446D Backhoe Loader Power Train Drive and Steering Axle (Front) - Remove
988H Wheel Loader Power Train Engagement Pressure for the Transmission Clutch (Operator Monitor) - Calibrate
2004/07/05 Improved Analysis of Non-Warrantable Failures for Reman Vane Cartridges {5055}
446D Backhoe Loader Power Train Steering Cylinder (Front) - Remove and Install
2004/07/01 Engines Are Now Built with Semi-Crowned Lifter Rollers {1209}
446D Backhoe Loader Power Train Tie Rod (Steering)(Front) - Remove and Install
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Machine Systems Front Frame from Rear Frame - Separate
2004/06/21 Special Instruction, REHS2149, "Explanation of Common Event Codes and Transmission Shift Matrix" is now Available {4800, 4808}
AP-800D and BG-230D Asphalt Pavers Machine Systems Truck Hitch
R2900G Load Haul Dump Machine Systems Bucket - Remove
R1300G Load Haul Dump 3306 Engine Supplement Air Cleaner - Remove and Install
R2900G Load Haul Dump Power Train Differential and Bevel Gear (Front) - Remove
R2900G Load Haul Dump Machine Systems Bucket - Install
2004/07/26 Correction to Disassembly and Assembly, RENR4884 , "Track (Rubber) - Remove and Install - 287B Multi Terrain Loader" {4198}
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Assemble - In Chassis
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Install
AP-800D and BG-230D Asphalt Pavers Machine Systems Solenoid Valve (Truck Hitch)
988H Wheel Loader Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Operator Monitor) - Calibrate
446D Backhoe Loader Power Train Transmission (Power Shift) - Remove
446D Backhoe Loader Power Train Transmission (Power Shift) - Disassemble