Differential and Bevel Gear (Front) - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-7405 | Eyebolt | 1 |
B | 138-7576 | Link Bracket | 2 |
Start By:
- Remove the front axle assembly. Refer to Disassembly and Assembly, "Fixed Axle (Front) - Remove".
- Remove the axle shafts. Refer to Disassembly and Assembly, "Axle Shaft - Remove".
Note: Cleanliness is an important factor. Before the removal procedure, clean the exterior of the component thoroughly. Cleanliness will help to prevent dirt from entering the internal mechanism.
- Remove yoke assembly (5).
- Disconnect four hose assemblies (1), (2), (3) and (4).
Show/hide table
Illustration 2 g01084693 - Remove bolts (7), cover (6) and shims (8).
Show/hide table
Illustration 3 g01084688 Typical example - Install Tooling (A) to pin (10). Remove pin (10).
- Remove O-ring seal (9) from pin (10).
Show/hide table
Illustration 4 g02740356 Show/hide tableIllustration 5 g02742417 - Position the fixed axle assembly in a suitable stand or on wood blocks with the pinion housing upward.
- Remove 20 bolts (11).
- Remove four special bolts (12).
Note: Bolts (12) are longer.
Show/hide tableIllustration 6 g02740357 - Attach Tooling (B) and a suitable lifting device to differential and bevel gear (13). The weight of differential and bevel gear (13) is approximately
415 kg (915 lb) . Remove differential and bevel gear (13).Show/hide tableIllustration 7 g02740376 - Remove O-ring seal (14).
Show/hide table
Illustration 1 | g01084681 |
Caterpillar Information System:
R1300G Load Haul Dump 3306 Engine Supplement Air Cleaner - Remove and Install
R2900G Load Haul Dump Machine Systems Bucket - Remove
AP-800D and BG-230D Asphalt Pavers Machine Systems Truck Hitch
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Disassemble - In Chassis
2004/08/02 New Proportional Control Handle Is Now Available {5705}
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Remove
446D Backhoe Loader Engine Supplement Hydraulic Oil Cooler - Remove and Install
446D Backhoe Loader Power Train Drive and Steering Axle (Front) - Install
446D Backhoe Loader Power Train Drive and Steering Axle (Front) - Remove
988H Wheel Loader Power Train Engagement Pressure for the Transmission Clutch (Operator Monitor) - Calibrate
2004/07/05 Improved Analysis of Non-Warrantable Failures for Reman Vane Cartridges {5055}
446D Backhoe Loader Power Train Steering Cylinder (Front) - Remove and Install
R2900G Load Haul Dump Machine Systems Bucket - Install
2004/07/26 Correction to Disassembly and Assembly, RENR4884 , "Track (Rubber) - Remove and Install - 287B Multi Terrain Loader" {4198}
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Assemble - In Chassis
446D Backhoe Loader Power Train Final Drive (Drive and Steering Axle)(Front) - Install
AP-800D and BG-230D Asphalt Pavers Machine Systems Solenoid Valve (Truck Hitch)
988H Wheel Loader Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Operator Monitor) - Calibrate
446D Backhoe Loader Power Train Transmission (Power Shift) - Remove
446D Backhoe Loader Power Train Transmission (Power Shift) - Disassemble
446D Backhoe Loader Power Train Transmission (Power Shift) - Assemble
446D Backhoe Loader Power Train Transmission (Power Shift) - Install
770 and 772 Off-Highway Truck Additional Messages
THP10 Series II and THP24S Series II Access Platform for Series B Telehandlers Caterpillar Approved Machines