Illustration 1 | g01058112 |
Linkage Pins     | |||||
Pins     | Pin Location     | Pin Diameter     | Pin Length     | Part Number (Assembly)     | Part Number (Pin)     |
1 (1)     | Arm to Felling Head     | 63.475 mm (2.4990 inch)     | 230 mm (9.0551 inch)     |
201-9694     | 201-9695     |
1 (2)     | Arm to Quick Coupler     | 63.48 mm (2.4992 inch)     |
270 mm (10.6299 inch)     |
242-9542     | 242-9543     |
2 (1)     | Link to Felling Head     | 50.78 mm (1.9992 inch)     |
154 mm (6.0630 inch)     |
201-9698     | 201-9699     |
2 (2)     | Link to Quick Coupler     | 50.78 mm (1.9992 inch)     |
259 mm (10.1968 inch)     |
242-9545     | 242-9546     |
3     | Link to Lever     | 50.78 mm (1.9992 inch)     |
154 mm (6.0630 inch)     |
201-9698     | 201-9699     |
4     | Lever to Cylinder     | 63.425 mm (2.4970 inch)     |
136 mm (5.3543 inch)     |
201-9696     | 201-9697     |
5     | Cylinder to Frame     | 63.475 mm (2.4990 inch)     |
230 mm (9.0551 inch)     |
201-9694     | 201-9695     |
6     | Arm to Frame     | 63.475 mm (2.4990 inch)     |
230 mm (9.0551 inch)     |
201-9694     | 201-9695     |
7     | Cylinder to Frame     | 63.475 mm (2.4990 inch)     |
230 mm (9.0551 inch)     |
201-9694     | 201-9695     |
8     | Cylinder to Arm     | 63.425 mm (2.4970 inch)     |
136 mm (5.3543 inch)     |
201-9696     | 201-9697     |
9     | Lever to Arm     | 50.78 mm (1.9992 inch)     |
154 mm (6.0630 inch)     |
201-9698     | 201-9699     |
( 1 ) | TK370 and TK380 |
( 2 ) | TK371 and TK381 |
Linkage Bearings     | ||||
Bearing     | Location of Bearing     | Bearing Diameter     | Depth at Assembly     | Part Number     |
1 (1)     | Arm to Felling Head     | 63.73 ± 0.05 mm (2.509 ± 0.002 inch)     |
6.4 ± 1 mm (0.2520 ± 0.0394 inch)     |
7J-9745     |
1 (2)     | Arm to Quick Coupler     | 63.73 ± 0.05 mm (2.509 ± 0.002 inch)     |
6.4 ± 1 mm (0.2520 ± 0.0394 inch)     |
7J-9745     |
2 (1)     | Link to Felling Head     | 50.96 ± 0.05 mm (2.006 ± 0.002 inch)     |
6.6 ± 1 mm (0.2598 ± 0.0394 inch)     |
3K-6575     |
2 (2)     | Link to Quick Coupler     | 50.96 ± 0.05 mm (2.006 ± 0.002 inch)     |
6.6 ± 1 mm (0.2598 ± 0.0394 inch)     |
3K-6575     |
3     | Link to Lever     | 50.96 ± 0.05 mm (2.006 ± 0.002 inch)     |
6.6 ± 1 mm (0.2598 ± 0.0394 inch)     |
3K-6575     |
4     | Cylinder to Lever     | 63.5 mm (2.5000 inch)     |
N/A     | 9J-3206     |
5     | Cylinder to Frame     | 63.5 mm (2.5000 inch)     |
N/A     | 9J-3206     |
6     | Arm to Frame     | 63.73 ± 0.05 mm (2.509 ± 0.002 inch)     |
6.4 ± 1 mm (0.2520 ± 0.0394 inch)     |
7J-9745     |
7     | Cylinder to Frame     | 63.5 mm (2.5000 inch)     |
N/A     | 9J-3206     |
8     | Cylinder to Arm     | 63.5 mm (2.5000 inch)     |
1.6 ± 1.0 mm (0.063 ± 0.039 inch)     |
9J-3206     |
9     | Lever to Arm     | 50.96 ± 0.05 mm (2.006 ± 0.002 inch)     |
6.6 ± 1 mm (0.2598 ± 0.0394 inch)     |
3K-6575     |
( 1 ) | TK370 and TK380 |
( 2 ) | TK371 and TK381 |
Linkage Seals     | ||
Seal     | Location of Seal     | Part Number     |
1     | Arm to Work tool     | 7K-9206     |
2     | Link to Work tool     | 7K-9203     |
3     | Link to Lever     | 7K-9203     |
6     | Arm to Frame     | 7K-9206     |
9     | Lever to Arm     | 7K-9203     |
Note: Lubricate all pin bores with 5P-0960 Molybdenum Grease . Lubricate the lips of all seals with the lubricant that is being sealed.
Illustration 2 | g01058320 |
(10) Install washers in order to minimize the gap to less than 1.2 millimeters. Use the same number of washers on each side of the arm plates. Also, use the same thickness of washers to the inner faces of the arm plates. Use the following washers:
Thickness of the 203-0325 Washer ... 1 mm (.04 inch)
Thickness of the 203-0327 Washer ... 2 mm (.08 inch)
(11) Coat the lip seals with a thin film of 5P-0960 Molybdenum Grease .
Illustration 3 | g01058336 |
TK370 and TK380 |
Illustration 4 | g01058601 |
TK371 and TK381 |
(12) Install washers in order to minimize the gap to less than 1.2 millimeters. Use the same number and thickness of washers to the inner faces of both arm plates. Use the following washers:
Thickness of the 203-0325 Washer ... 1 mm (.04 inch)
Thickness of the 203-0327 Washer ... 2 mm (.08 inch)
(13) Coat the lip seals with a thin film of 5P-0960 Molybdenum Grease .