Accumulator Arm - Assemble - HF221 and HF222
Assembly Procedure
Show/hide table
Accidental machine starting can cause injury or death to personnel working on the machine. To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps. Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on. |
- Place rubber band (5) into outer accumulator arm (3) .
Show/hide table
Illustration 1 | g00757972 |
- Insert pin (8) into outer accumulator arm (3). Make sure that rubber band (5) is inside pin (8) .
- Attach a hoist and a suitable lifting device to outer accumulator arm (3). The weight of outer accumulator arm (3) is 30 kg (65 lb).
- Insert outer accumulator arm (3) into inner accumulator arm (2) .
Show/hide table
Illustration 2 | g00757961 |
- Insert pivot pin (7) .
- Insert bolt (6) and the nut into pivot pin (7) .
Tighten the locknut (10) until the clearance between the inner accumulator arm (2) and the outer accumulator arm (9) is 1 ± .5 mm (.04 ± .02 inch).
Show/hide table
Illustration 3 | g01064060 |
- Remove the hoist and the lifting device from outer accumulator arm (3) .
Show/hide table
Illustration 4 | g00757962 |
- Place rubber band (5) inside pin (1). Insert pin (1) into inner accumulator arm (2).
- Insert bolt (4) into pin (1).
Caterpillar Information System:
HF181, HF201, HF202, HF221 and HF222 Felling Heads Felling Head Accumulator Arm - Disassemble - HF221 and HF222
HF181, HF201, HF202, HF221 and HF222 Felling Heads Felling Head Hydraulic Cylinder (Accumulator Arm) - Remove and Install - HF221 and HF222
AP-655C and BG-2255C Asphalt Pavers Machine Systems Control Valve (Hydraulic Generator) - Install - CDG1-Up and CKR1-Up
AP-655C and BG-2255C Asphalt Pavers Machine Systems Control Valve (Hydraulic Generator) - Remove - CDG1-Up and CKR1-Up
C13, C15, and C18 Generator Set Engines Engine Cranks but Will Not Start
PS-150C Pneumatic Compactor Propel System Flow Divider Valve
CB-334E and CB-335E Vibratory Compactors Machine Systems Water Spray Pump Flow - Test
IQAN® Monitoring ; Control System IQAN Screen Flow Chart
HF181, HF201, HF202, HF221 and HF222 Felling Heads Felling Head Grapple Arm - Remove - HF221 and HF222
HF202 Felling Head, HF221 Felling Head and HF222 Felling Head for Wheel Feller Bunchers Hydraulic Cylinder (Grapple Arm) - Remove and Install - HF221 and HF222
267B, 277B and 287B Multi Terrain Loaders Power Train Piston Pump (Hydrostatic) - Remove - 287B Multi Terrain Loader
2004/03/15 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Center) - Assemble" {3256, 3258}
HF181, HF201, HF202, HF221 and HF222 Felling Heads Felling Head Accumulator Arm - Install - HF221 and HF222
CB-334E and CB-335E Vibratory Compactors Machine Systems Water Spray System Troubleshooting
AP-655C and BG-2255C Asphalt Pavers Machine Systems Control Valve (Hydraulic Generator) - Disassemble - AYP1-Up and B9G1-Up
AP-655C and BG-2255C Asphalt Pavers Machine Systems Control Valve (Hydraulic Generator) - Assemble - AYP1-Up and B9G1-Up
3408E and 3412E Engines for Caterpillar Built Machines CID 0164 FMI 04 Injector Actuation Pressure voltage low
120H and 135H Motor Graders Air System and Brakes Check Valve (Air Tank)
267B, 277B and 287B Multi Terrain Loaders Power Train Piston Pump (Hydrostatic) - Install - 287B Multi Terrain Loader
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Water Spray Pump Flow - Test
TK370 Wheel Feller Buncher, TK380 Wheel Feller Buncher, TK371 Industrial Tractor and TK381 Industrial Tractor Machine Systems Work Tool Linkage
PS-150C Pneumatic Compactor Machine System Steering Control
CB-334E and CB-335E Vibratory Compactors Machine Systems Hydraulic Cylinder (Steering)
PS-150C Pneumatic Compactor Machine System Oscillating and Steering Bar