Suspension System - Check
Show/hide table
 |
|
Sistem suspensi dapat menyebabkan alat berat turun dengan tiba-tiba hingga menyebabkan tidak adanya ruang gerak yang cukup antara rumah gandaran, rangka utama, ban dan pelat pelindung lumpur. Bekerja di daerah ini dapat mengakibatkan terjadinya cedera atau kematian akibat terjepit. Parkir alat berat pada permukaan yang datar dan ganjal rangka depan sebelum masuk ke bagian bawah alat berat. |
- Nonaktifkan pengunci diferensial. Hentikan alat berat secara perlahan pada permukaan tanah yang rata dan keras.
- Lepaskan rem servis. Tunggu selama satu detik sebelum menerapkan rem parkir.
- Pasang penyangga yang sesuai di bawah rangka depan.
Show/hide table
Ilustrasi 1 g01043895 - Ukur jarak (A). Jarak (A) adalah jarak antara pin pemasangan silinder suspensi. Dimensi (A) seharusnya adalah
700 ± 10 mm (27.6 ± 0.39 inch) .Catatan: Ukur jarak (A) saat alat berat dingin.
- Jika ketinggian suspensi tidak sesuai, hubungi dealer Caterpillar Anda. Alat dan prosedur khusus diperlukan untuk menyetel ketinggian suspensi depan.
- Lepaskan penyangga.
Caterpillar Information System:
247B, 257B, 267B, 277B and 287B Multi Terrain Loaders and 216B, 226B, 232B, 236B, 242B, 246B, 248B, 252B, 262B and 268B Skid Steer Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1935 - FMI 04
CB-214E, CB-224E and CB-225E Paving Compactors Seat
2004/03/15 A Seal Kit for the Retract Section of the Hydraulic Pump Is Now Available {5055, 5070}
2004/03/15 Changes to the Steering System {4300}
2003/12/29 A New Retaining Ring Is Now Used in the Forward Low and Reverse Clutches {3155}
2003/12/29 New Retaining Ring in Gear Clutch Is Now Used. {3155}
R1300G Load Haul Dump Power Train Trunnion Support (Oscillating Axle, Rear) - Remove
R2900G Load Haul Dump Power Train Electronic Control System Electronic Control Module (Power Train) - Replace
R2900G Load Haul Dump Power Train Electronic Control System Connector Locations
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
C13, C15, and C18 Generator Set Engines E197 High Engine Oil Temperature
446D Backhoe Loader Engine Oil and Filter - Change
CP-323C and CS-323C Paving Compactors Cooling System Coolant Extender (ELC) - Add
446D Backhoe Loader Hydraulic and Steering System Signal Resolver Network
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Control Valve
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Kickout and Positioner - Adjust
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install - If Equipped
248B and 268B Skid Steer Loaders Engine Supplement Radiator and Hydraulic Oil Cooler - Install
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Normal Operation
914G2 and IT14G2 Compact Wheel Loaders Radiator Core - Clean
M325D and M330D Excavators Power Train Electronic Control System General Information
CP-323C and CS-323C Paving Compactors Cooling System Water Temperature Regulator - Replace
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Relief Valve (Hoist)