Relief Valve (Hoist)
Show/hide table
Illustration 1 | g00850224 |
Relief pressure (raise) ... 20700 ± 340 kPa (3002 ± 49 psi)
Relief pressure (lower) ... 6900 ± 340 kPa (1000 ± 49 psi)
Note: Test the valve at 49° ± 3°C (120° ± 5° F).
Note: Set 22500 kPa (3000 psi) before 6900 kPa (1000 psi).
(1) Torque for installing the relief valve ... 110 ± 5 N·m (74 ± 4 lb ft)
(2) Lubricate the seal lightly with clean hydraulic fluid.
(3) Torque for the relief valve body ... 110 ± 10 N·m (81 ± 7 lb ft)
(4) 8H-3532 Spring
- Test force ... 95 ± 7 N (21 ± 1.5 lb)
- Test length ... 25.4 mm (1 inch)
- Free length after test ... 42 mm (1.6535 inch)
- Outside diameter ... 11.93 mm (0.47 inch)
- Test length ... 25.4 mm (1 inch)
(5) 171-5910 Spring
- Test force ... 129.3 ± 10.2 N (29.1 ± 2.3 lb)
- Test length ... 33.27 mm (1.31 inch)
- Free length after test ... 36.09 mm (1.42 inch)
- Outside diameter ... 11.68 mm (0.45 inch)
- Test length ... 33.27 mm (1.31 inch)
(6) Change the thickness of the shim pack in order to set relief pressure for raising the body.
Show/hide table
Shims for the relief pressure for lowering the body     | ||
Pt. No. for Shim     | Thickness     | Approximate change in pressure     |
4M-6978 Shim     | 0.508 mm (0.02 inch)     |
2950 kPa (430 psi)     |
4M-6979 Shim     | 1.27 mm (0.05 inch)     |
7370 kPa (1070 psi)     |
4M-6980 Shim     | 0.254 mm (0.01 inch)     |
1470 kPa (210 psi)     |
4T-4659 Shim     | 0.8 mm (0.0315 inch)     |
4640 kPa (670 psi)     |
(7) Change the thickness of the shim pack in order to set relief pressure for lowering the body.
Show/hide table
Shims for the relief pressure for raising the body     | ||
Pt. No. for Shim     | Thickness     | Approximate change in pressure     |
3J-7473 Shim     | 0.12 mm (0.005 inch)     |
700 kPa (100 psi)     |
3H-2549 Shim     | 0.254 mm (0.0100 inch)     |
1470 kPa (210 psi)     |
4T-4660 Shim     | 0.08 mm (0.003 inch)     |
460 kPa (67 psi)     |
3J-7470 Shim     | 1.22 mm (0.048 inch)     |
7070 kPa (1030 psi)     |
Caterpillar Information System:
CP-323C and CS-323C Paving Compactors Cooling System Water Temperature Regulator - Replace
M325D and M330D Excavators Power Train Electronic Control System General Information
914G2 and IT14G2 Compact Wheel Loaders Radiator Core - Clean
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Normal Operation
248B and 268B Skid Steer Loaders Engine Supplement Radiator and Hydraulic Oil Cooler - Install
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install - If Equipped
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Kickout and Positioner - Adjust
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Control Valve
446D Backhoe Loader Hydraulic and Steering System Signal Resolver Network
CP-323C and CS-323C Paving Compactors Cooling System Coolant Extender (ELC) - Add
735 Articulated Truck Suspension System - Check
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Hydraulic Accumulator (Pilot Oil) - Test and Charge
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Ride Control Accumulator - Test and Charge
C13, C15, and C18 Generator Set Engines E199 Low Coolant Temperature
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Secondary Steering Valve - If Equipped
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Electronic Control Module (ECM)
C13, C15, and C18 Generator Set Engines E360 Low Engine Oil Pressure
Procedure to Convert a Segmented Disc Saw to a One-Piece Disc Saw{6543} Procedure to Convert a Segmented Disc Saw to a One-Piece Disc Saw{6543}
914G2 and IT14G2 Compact Wheel Loaders Bucket Pivot Bearings - Lubricate
CP-323C and CS-323C Paving Compactors Cutting Edges (Leveling Blade) - Inspect/Replace
R2900G Load Haul Dump Power Train Electronic Control System MID 081 - CID 0363 - FMI 03
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Sensors
R2900G Load Haul Dump Power Train Electronic Control System MID 081 - CID 0363 - FMI 05