Incorrect Pressure Specification For PiIot System Pressure Test
Usage:
MINI-HYDRAULIC EXCAVATORS301.5 (3YW1-UP) MINI-HYDRAULIC EXCAVATORS
Problem:
Reference: SERVICE MAGAZINE; MAY 17, 1999; PAGE 5; "CORRECTION TO TESTING AND ADJUSTING MANUAL, RENR2806.
Reference: " REFERENCE: SERVICE MANUAL MODULE, RENR2806; TESTING AND ADJUSTING; 301.5 MINI HYDRAULIC EXCAVATOR; PAGE 13.
The pressure that is specified in Step 8 of the Pilot System Pressure Test Procedure in the Testing and Adjusting Manual and in the May 17, 1999 Service Magazine article, "Correction to Testing and Adjusting Manual, RENR2806" is incorrect.
Solution:
The correct pressure is 3100 ± 300 kPa (450 ± 44 psi).
COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar Information System:
Tire Performance Problems On Off Highway Trucks Can Be Prevented Tire Performance Problems On Off Highway Trucks Can Be Prevented
Proper Orientation of the Rod Yoke Prevents Interference with the Stick During Extension on Some Excavators Proper Orientation of the Rod Yoke Prevents Interference with the Stick During Extension on Some Excavators
The Fan Guard Mounts May Fail Prematurely on 5110B Excavtors The Fan Guard Mounts May Fail Prematurely on 5110B Excavtors
FINAL DRIVE SPINDLE BEARINGS MAY FAIL FINAL DRIVE SPINDLE BEARINGS MAY FAIL
DISASSEMBLY OF THE STICK CYLINDERS AND OF THE BUCKET CYLINDERS MAY BE DIFFICULT DISASSEMBLY OF THE STICK CYLINDERS AND OF THE BUCKET CYLINDERS MAY BE DIFFICULT
Some Pumps May Have the Incorrect Actuator Some Pumps May Have the Incorrect Actuator
THE WELD BETWEEN THE TOP PLATE AND THE SIDE PLATE BELOW THE STICK BRACKETS MAY CRACK THE WELD BETWEEN THE TOP PLATE AND THE SIDE PLATE BELOW THE STICK BRACKETS MAY CRACK
Some 2P-4472, 7G-0825, and 8P-1656 Clutch Plates May Have Been Shipped Into the Parts System Before Finish Grinding Some 2P-4472, 7G-0825, and 8P-1656 Clutch Plates May Have Been Shipped Into the Parts System Before Finish Grinding
Certain Wheel-Tractor Scrapers May Experience Leadking at the Final Drive Oil Drain Hole Certain Wheel-Tractor Scrapers May Experience Leadking at the Final Drive Oil Drain Hole
HYDRAULIC TANK FILLER TUBE STRAINER MAY RUST HYDRAULIC TANK FILLER TUBE STRAINER MAY RUST
OPERATION OF BUCKET MAY EXPERIENCE A CYCLING SURGE OPERATION OF BUCKET MAY EXPERIENCE A CYCLING SURGE
224-7252 XT-6 ES HOSE ASSEMBLY WILL NOT FIT CORRECTLY 224-7252 XT-6 ES HOSE ASSEMBLY WILL NOT FIT CORRECTLY
Check For Correct Operation Of Oil Level Switch Check For Correct Operation Of Oil Level Switch
SCHEDULED OIL SAMPLING (SOS) RESULTS ON BACKHOE LOADERS SCHEDULED OIL SAMPLING (SOS) RESULTS ON BACKHOE LOADERS
Generator Lead Connections Can Rub Against The Terminal Box Or Each Other Generator Lead Connections Can Rub Against The Terminal Box Or Each Other
Specifications For Certain Pressures And Some Engine Speeds Are Corrected For Heavy Lift Control Specifications For Certain Pressures And Some Engine Speeds Are Corrected For Heavy Lift Control
Can Not Perform Calibration Of The Governor Actuator With The "PDT" Or With A Laptop And M300 Technician Or Engine Constantly Runs At Low Idle Can Not Perform Calibration Of The Governor Actuator With The "PDT" Or With A Laptop And M300 Technician Or Engine Constantly Runs At Low Idle
Gear Pump For The Brake, Pilot And Steering System May Have Failures To Front Bearing Or Front Shaft Gear Pump For The Brake, Pilot And Steering System May Have Failures To Front Bearing Or Front Shaft
Inspect Track Seal Load Rings Inspect Track Seal Load Rings
Oil Pan Cracking Oil Pan Cracking
Unlatched Condition Of Operator Console (Armrest) May Prevent Or Interrupt Machine Operations Unlatched Condition Of Operator Console (Armrest) May Prevent Or Interrupt Machine Operations
Backup Switch For The Auxiliary Controller May Be Wired Incorrectly Backup Switch For The Auxiliary Controller May Be Wired Incorrectly
The Low Idle RPM May Drop Below Specifications The Low Idle RPM May Drop Below Specifications
Oil In Turbochargers Oil In Turbochargers