A New Speed-Timing Sensor is Now Available {1912}
- Off-Highway Truck/Tractor:
- 776D (S/N: 5ER1-UP; AFS1-UP)
- Excavator:
- 5130 (S/N: 7TJ1-UP)
- Track-Type Tractor:
- D11R (S/N: 7PZ1-UP; 9TR1-UP; 9XR1-UP; AAF1-UP)
- Wheel Dozer:
- 854G (S/N: 1JW1-UP; A4W1-UP; AMP1-UP)
- Wheel Loader:
- 992G (S/N: 7HR1-UP; ADZ1-UP; AZX1-UP)
- 777D (S/N: 2YW1-UP; 3PR1-UP; AGC1-UP; AGY1-UP)
- 784C (S/N: 2PZ1-UP)
- 785C (S/N: 1HW1-UP; 5AZ1-UP; APX1-UP)
- 789C (S/N: 2BW1-UP)
- 793C (S/N: 4AR1-UP; 4GZ1-UP; ATY1-UP; CBR1-UP)
- 793D (S/N: FDB1-UP)
- 797 (S/N: 5YW1-UP)
- 797B (S/N: JSM1-UP)
- 5130B (S/N: 4CS1-UP)
- 5230B (S/N: 4HZ1-UP)
- 994D (S/N: 3TZ1-UP)
- 994F (S/N: 4421-UP)
A new speed-timing sensor group is now available. The 273-5041 Speed Sensor Group replaces the 129-6628 Speed Sensor Group. The improved design will enhance the sensitivity of the speed-timing sensor. No adjustments are necessary for installation.
Replacing an old non-defective speed-timing sensor group with a new sensor group is not a warrantable repair.
Caterpillar Information System:
Bench Test Procedure For A MT835, MT845, MT855, MT865, MTC835, MTC845, MTC855, and MTC865 Agricultural Tractor Transmission {3030, 3073} Bench Test Procedure For A MT835, MT845, MT855, MT865, MTC835, MTC845, MTC855, and MTC865 Agricultural Tractor Transmission {3030, 3073}
416E, 422E and 428E Backhoe Loaders Hydraulic and Steering System Hydraulic Lockout Function
AS2302 Vers-A-Mat Screed Screed Chain (Crown) - Remove and Install
THP10 Series II and THP24S Series II Access Platform for Series B Telehandlers Rotary Actuator - Remove and Install
Metal Shavings in the Hydraulic Electronic Unit Injector (HEUI) Oil Passages{1250, 1274} Metal Shavings in the Hydraulic Electronic Unit Injector (HEUI) Oil Passages{1250, 1274}
AS2302 Vers-A-Mat Screed Shoe (End Gate) - Remove and Install
AS2302 Vers-A-Mat Screed Actuator (End Gate) - Remove and Install
14M and 16M Motor Graders Machine Systems Battery
14M and 16M Motor Graders Machine Systems Battery
Installation of a New Hydraulic Pump and a New Suction Hose Can Improve Service Life of Certain Telehandlers{5057, 5070} Installation of a New Hydraulic Pump and a New Suction Hose Can Improve Service Life of Certain Telehandlers{5057, 5070}
AS2302 Vers-A-Mat Screed End Gate - Remove and Install
C4.4 Industrial Engine Valve Depth - Inspect
572R Series II Pipelayer Operator Controls
R1700G Load Haul Dump Steering System Steering Cylinder Mounting
R1700G Load Haul Dump Battery Isolation Control - If Equipped
2006/06/26 A New Lens for the Rear Signal Lamp Is Available {1430}
2006/06/26 New Pilot Line for the Hoist Control Valve Is Available {5136}
C4.4 Industrial Engine Engine Oil Pressure - Test
2006/06/26 The Addition of Spacer Plates Avoids Contact Between Ejector Frames and End Plates {6203, 7271}
2006/07/24 Improved Pin for the Transport Lock Is Used {6203, 7505}
AS2302 Vers-A-Mat Screed Drive Shaft (Crown) - Remove
AS2302 Vers-A-Mat Screed Drive Shaft (Crown) - Disassemble
AS2302 Vers-A-Mat Screed Drive Shaft (Crown) - Assemble
AS2302 Vers-A-Mat Screed Drive Shaft (Crown) - Install