Swing Motor - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
B     | 1P-1857     | Retaining Ring Pliers     | 1     |
- Raise the temperature of bearing (29) .
Show/hide table
Illustration 1 | g01188434 |
- Install bearing (29) onto shaft (30) .
- Install ring (32) onto bearing (29) .
- Lower the temperature of bearing (29) and shaft (30) .
Show/hide table
Illustration 2 | g01188435 |
- Install bearing (29) and shaft (30) .
- Install plate (28) .
- Install washers (26) and spring (27) .
Show/hide table
Illustration 3 | g01188431 |
- Use a suitable press and Tooling (B) in order to install retaining ring (25) .
Show/hide table
Illustration 4 | g01188430 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
- Install pins (24) .
Show/hide table
Illustration 5 | g01188428 |
- Install bearing (23), retainer (22), and pistons (21) .
Show/hide table
Illustration 6 | g01188427 |
- Install rotating group (20) and plates (19) .
Show/hide table
Illustration 7 | g01188426 |
- Install O-ring seals (18) .
Show/hide table
Illustration 8 | g01188425 |
- Install piston (16) and pins (17) .
Show/hide table
Illustration 9 | g01188997 |
- Install spacer (14), bevel washer (13), and O-ring seal (15) .
Show/hide table
Illustration 10 | g01188422 |
- Install bevel washer (12) and spacer (11) .
Show/hide table
Illustration 11 | g01188421 |
- Install bearing (10), port plate (9), and O-ring seal (8) .
Show/hide table
Illustration 12 | g01188420 |
- Install head (6) and bolts (7) .
Show/hide table
Illustration 13 | g01188419 |
- Tighten bolts (7) to a torque of 128 ± 7 N·m (94 ± 5 lb ft).
- Install the O-ring seals, plug (3), check valve (4), and plug (5) .
Show/hide table
Illustration 14 | g01188418 |
- Tighten plug (3) to a torque of 12 ± .5 N·m (106 ± 4 lb in).
- Tighten check valve (4) to a torque of 157 ± 10 N·m (116 ± 7 lb ft).
- Install the O-ring seal, plug (1), and check valve (2) .
Show/hide table
Illustration 15 | g01188417 |
- Tighten plug (1) to a torque of 39 ± 2 N·m (345 ± 18 lb in).
End By: Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Caterpillar Information System:
302.5C Mini Hydraulic Excavator Machine Systems Swing Motor - Disassemble
302.5C Mini Hydraulic Excavator Machine Systems Swing Gear and Bearing - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism
302.5C Mini Hydraulic Excavator Machine Systems Upper Frame and Undercarriage Frame - Connect
365C Excavator Machine Systems Control Manifold (Pilot Oil) - Install
365C Excavator Machine Systems Control Manifold (Pilot Oil) - Remove
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Fuel Tank Cap and Strainer - Clean
345C MHPU Mobile Hydraulic Power Unit Machine Systems Main Control Valve - Assemble
345C MHPU Mobile Hydraulic Power Unit Machine Systems Main Control Valve - Disassemble
Pin Grabber Quick Hitch Quick Coupler Installation and Removal
Pin Grabber Quick Hitch Quick Coupler - Lubricate
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Muffler - Remove and Install
365C Excavator Machine Systems Relief Valve (Pilot) - Install
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Exhaust Manifold - Remove and Install
365C Excavator Machine Systems Pedal Control (Travel) - Remove
365C Excavator Machine Systems Pedal Control (Travel) - Install
302.5C Mini Hydraulic Excavator Machine Systems Bucket Cylinder - Remove and Install
2007/09/03 Replacement of the 223-3383 Washer Pump As on Certain Motor Graders and Track-Type Tractors {7306}
365C Excavator Machine Systems Oil Filter (Hydraulic, Return) - Remove
365C Excavator Machine Systems Oil Filter (Hydraulic, Return) - Install
Pin Grabber Quick Hitch Plate Locations and Film Locations
M318C and M322C Excavators Machine Systems Hydraulic Tank and Filter - Remove
M318C and M322C Excavators Machine Systems Hydraulic Tank and Filter - Install
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Hydraulic System Oil - Change