Alternator - Assemble - M1 Series Alternator (35 Amp)
Assembly Procedure
Note: Before assembly, clean all parts in cleaning fluid. Allow the parts to air dry. DO NOT dry the parts with wiping cloths or with rags. Cloths and rags contain lint. Inspect all parts. Replace worn parts and replace damaged parts.
- Put field winding (24) into the rear frame. Install three bolts.
Show/hide table
 | |
| Illustration 1 | g00825771 |
- Install "R" terminal (19). Put rectifier (23) into the rear frame. Install the four bolts. Tighten the "B+" terminal nut to the following torque: 29 ± 8 N·m (21 ± 6 lb ft) Tighten the "B-" terminal nut to the following torque: 4.4 ± 1 N·m (39 ± 9 lb in)
Show/hide table
 | |
| Illustration 2 | g00825773 |
- Put rear frame (4) on stator (5). Align the marks on the stator and on the rear frame. Connect the stator leads to the rectifier.
Show/hide table
 | |
| Illustration 3 | g00825774 |
- Install regulator (15) and capacitor (17). Install the two bolts.
Show/hide table
 | |
| Illustration 4 | g00825775 |
- Connect the field winding leads and connect the wire (14) to the regulator and to the capacitor. Connect the other end of the wire (14) and connect wire (16) to the rectifier.
- Install the rear cover.
- Install two ball bearings (6) on the rotor. Install plate assembly (10), the rear spacer, the rear felt washer, plate (7), ball bearing (8), washer (11), front felt washer (12), and spacer (9) .
Show/hide table
 | |
| Illustration 5 | g00825750 |
- Put rotor (26) into the front frame. Install the four bolts.
Show/hide table
 | |
| Illustration 6 | g00825777 |
- The rotor remains connected to the front frame. The stator remains connected to the rear frame. Put front frame (3) into the rear frame (4). Align the marks on the front frame and on the rear frame. Install the four bolts.
Show/hide table
 | |
| Illustration 7 | g00825778 |
- Install the fan, the key, the pulley, the washer, and the pulley nut. Tighten the pulley nut to the following torque: 102 ± 7 N·m (75 ± 5 lb ft)
- Restore the residual magnetism in the alternator. Refer to Testing and Adjusting, "Residual Magnetism - Restore".
End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Caterpillar Information System:
3512B Marine Auxiliary Engine Speed Control
3412E, C30 and C32 Marine Engines Exhaust Manifold - Remove and Install
TK711, TK721, TK722 and TK732 Track Feller Bunchers Seat Belt - Replace
3054 and 3056 Industrial and Generator Set Engines Maintenance Interval Schedule
3512B Marine Auxiliary Engine System Configuration Parameters
3512B Marine Auxiliary Engine Engine Monitoring System
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Disassemble - M1 Series Alternator (35 Amp)
G3500 Engines Manifold Air Pressure Sensor
C15 Petroleum Generator Set Engines Electronic Unit Injector - Adjust
G3408C and G3412C Engines Connecting Rod Bearings - Remove and Install
G3406 Engine Starting System
3608 Engine Marine Monitoring System Connector Contact Description
G3408C and G3412C Engines Balancer Group - Rear
3126B Marine Engines Sensors and Electrical Connectors
2001/08/01 Be Sure To Check The Counterweights On The Engine Crankshaft For Counterweight Sequence Numbers {1231}
HDB Series and M1 Series Heavy Duty Brushless Alternators Field Winding - Test
G3600 Engines Aftercooler
HDB Series and M1 Series Heavy Duty Brushless Alternators Capacitor - Test
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Remove
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Install
HDB Series and M1 Series Heavy Duty Brushless Alternators Stator - Test
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Disassemble
HDB Series and M1 Series Heavy Duty Brushless Alternators Rectifier - Test
2001/08/01 Oil Pan No Longer Requires Gasket Sealant {1302}