Connecting Rod Bearings - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9S-9082     | 发动机盘车工具     | 1     |
开始:
- 拆下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 检查连杆和连杆轴承盖,以便确认并定位在曲轴上。
- 使用工具 (A) 转动飞轮以便可以接触要拆卸的连杆盖。
- 将螺母 (1) 和连杆轴承盖 (2) 从连杆上拆下。
Show/hide table
图 1 | g00786899 |
- 将连杆从曲轴内推出并拆卸连杆轴承的上半部分。
- 从连杆盖 (2) 上拆卸连杆轴承的下半部分 (1) 。
Show/hide table
图 2 | g00568856 |
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
B     | -     | 塑料线间隙规     | -     |
C     | 4C-5593     | 防粘结剂     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 当间隙检查完成后,安装连杆轴承,并保持干燥。 为了便于最终组装,在连杆轴承上涂抹清洁的发动机机油。
注: 有关测量连杆轴承间隙的完整详细信息,请参阅专门出版物, "发动机轴承和曲轴"。
- 在连杆轴承盖 (2) 中安装一个新的连杆轴承 (1) 下半部分。
Show/hide table
图 3 | g00514587 |
- 在连杆内安装新的连杆轴承上半部分。
- 拉动曲轴上的连杆。
Show/hide table
图 4 | g00568856 |
- 使用工具 (B) 检查连杆轴承间隙。 按照步骤 5 和 6,在检查间隙时正确地安装和拧紧连杆轴承盖。 请参阅拆解与组装, "轴承间隙 – 检查"。
轴承间隙(新轴承) ... 0.071 至 0.168 mm (0.0028 至 0.0066 in)
最大容许轴承间隙(旧轴承) ... 0.25 mm (0.010")
- 使用工具 (C) 润滑连杆螺栓的螺纹和连杆轴承盖 (2) 的座面。 安装连杆轴承盖 (2) 和螺母 (3) 。 确保连杆轴承盖一侧的数字和连接杆上的数字在同一侧。
- 如下所述,拧紧螺母 (3) :
- 拧紧螺母至扭矩 82 ± 8 N·m (60 ± 6 lb ft)。
- 在每个螺母和每个连杆轴承盖上做上标记。
- 将各螺母再拧 120 ± 5 度。
- 重复步骤 1 至 6 以便安装其余的连杆。
End By: 安装活塞冷却喷嘴。 请参阅 拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Caterpillar Information System:
G3406 Engine Starting System
3608 Engine Marine Monitoring System Connector Contact Description
3608 Engine Marine Monitoring System Central Processing Unit - Replace
G3406 Engine Grounding Practices
3608 Engine Marine Monitoring System Memory Module - Replace
3126E Truck Engines Exhaust Brake
3608 Engine Marine Monitoring System Battery - Replace
3608 Engine Marine Monitoring System Speed Sensor - Adjust
3608 Engine Marine Monitoring System Performance Tests
3608 Engine Marine Monitoring System System Tests
3608 Engine Marine Monitoring System Overspeed Verification Test
3608 Engine Marine Monitoring System Resistance Temperature Detector
C15 Petroleum Generator Set Engines Electronic Unit Injector - Adjust
G3500 Engines Manifold Air Pressure Sensor
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Disassemble - M1 Series Alternator (35 Amp)
3512B Marine Auxiliary Engine Engine Monitoring System
3512B Marine Auxiliary Engine System Configuration Parameters
3054 and 3056 Industrial and Generator Set Engines Maintenance Interval Schedule
TK711, TK721, TK722 and TK732 Track Feller Bunchers Seat Belt - Replace
3412E, C30 and C32 Marine Engines Exhaust Manifold - Remove and Install
3512B Marine Auxiliary Engine Speed Control
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Assemble - M1 Series Alternator (35 Amp)
G3408C and G3412C Engines Balancer Group - Rear
3126B Marine Engines Sensors and Electrical Connectors