Change to Specifications Manual {1157}
- Industrial Engines:
- C-10 (S/N: BCX)
- Marine Engines:
- 3176C (S/N: 6BW)
- C-12 (S/N: BDL; CPN; JAC)
- 3176C (S/N: 5DZ; CRJ)
- 3196 (S/N: 2XR)
Reference: A torque sequence for the bolts that mount the flywheel housing to the cylinder block has been added to the specifications for the flywheel housings on these engines. This change is shown in the text that follows. This change will be included in the next revision of these manuals.
Show/hide table
Illustration 1 | g00877675 |
(1) Apply 1U-6396 O-Ring Assembly Compound to the O-Ring. Install the O-Ring.
Show/hide table
Illustration 2 | g00877679 |
Show/hide table
Illustration 3 | g00871606 |
Torque sequence |
(2) Flywheel housing
(3) Apply 1U-8846 Sealant on the gasket surface of the flywheel housing. Assemble the flywheel housing to the cylinder block and tighten within ten minutes of applying the sealant. Use the torque sequence that is shown in Illustration 3 to tighten the bolts.
(4) Cylinder block
Caterpillar Information System:
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0967 - FMI 02
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0826 - FMI 04
2002/05/27 Preparation of Air Conditioner Units for Seasonal Use {7320}
Instructions for Updating the CABSDos Software and Reinstalling the CABSDos Software{7610, 7620} Instructions for Updating the CABSDos Software and Reinstalling the CABSDos Software{7610, 7620}
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0826 - FMI 03
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Transmission Charging Pump Pressure - Test
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0709 - FMI 06
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0709 - FMI 05
2002/06/24 Correction to Specifications , "Pressure Control Valve (Transmission)" {3074}
RM-350B Reclaimer Mixer Machine Electronic Control System Using Caterpillar Monitoring System to Determine Diagnostic Codes
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Oil Level - Check
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0709 - FMI 03
Installation Procedure for Installing a Blade on 574 Forwarders{6060} Installation Procedure for Installing a Blade on 574 Forwarders{6060}
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Transmission Pressures - Test
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors System Configuration Parameters
IQAN<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Monitoring ; Control System Retrieving and Saving Parameter Files
2002/04/01 New Connectors are Used on the Gear Shift Harness {1408}
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Initial Pressures - Test and Adjust
2002/06/24 Correction to Testing and Adjusting , "Transmission Hydraulic Control Primary Clutch Pressure - Test and Adjust" {3167}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Fuel Tank Water and Sediment - Drain
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Hydraulic System Pilot Valve - <B>190-6722</B> Pilot Valve
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0967 - FMI 09
RM-350B Reclaimer Mixer Machine Electronic Control System Propel Lever - Calibrate
2002/06/24 Correction to Testing and Adjusting , "Transmission Hydraulic Control Clutch Pressure - Test" {3167}