System Configuration Parameters
System configuration parameters are parameters that affect emissions and power of the engine applications. Default values for the parameters are programmed at the factory. Some parameters may be changed by the customer in order to suit the needs of the specific application. System configuration parameters consist of ECM Identification Parameters and Selected Engine Rating Parameters. You must reprogram the ECM Identification Parameters if the ECM is replaced and/or you reprogram the engine rating. It is not necessary to reprogram the ECM Identification Parameters if a new personality module is "flashed in". Proper values for these parameters are available on the electronic service tool. Certain configuration parameters are also stamped on the engine information plate.
Note: If the parameters that are protected with the factory passwords are changed, the Caterpillar warranty may be voided.
System Configuration Parameters
Show/hide table
System Configuration Parameters     | |||||
---|---|---|---|---|---|
Parameter     | Available Range or Options     | Default     | Required Password     | ||
"Equipment ID"     | 17 alphanumeric characters     |     | None     | ||
"Engine Serial Number"     | 0XX00000 or XXXX00000     |
    | None     | ||
"ECM Serial Number"     |     |     | Read Only (1)     | ||
"Personality Module Part Number"     |     |     | Read Only (1)     | ||
"Personality Module Description"     |     |     | Read Only (1)     | ||
"Full Load Setting (FLS)"     | Programmed at the Factory     | 10     | Factory     | ||
Full Torque Setting (FTS)     | Programmed at the Factory     | -2     | Factory     | ||
"Idle Shutdown Time"     | 0 to 20 minutes     | 0     |     | ||
"Shutdown Timer"     | "Enabled or Disabled"     | Disabled     |     | ||
"Lighting Shutdown Timer Enable Status"     | "Enabled or Disabled"     | Disabled     |     | ||
"Lighting Shutdown Timer Duration"     | 0 to 15 min     | 0 minutes     |     | ||
"Deceleration Pedal Installation Status"     | "Decelerator Switch, Decelerator Pedal, Not Installed"     | "Not Configured"     |     | ||
"Max Deceleration Pedal Positive Engine Speed"     | 1000 RPM to 2300 RPM     | 1200     |     | ||
"Ground Speed Radar Installation Status"     | "Enabled or Disabled"     | "Enabled"     | None (2)     | ||
"Engine Oil Weight"     | "0W20", "10W30", "15W40"     | "10W 30 oil grade"     |     | ||
Total Tattletale     |     | 5     |     | ||
Engine Idle Speed     | 700-1000     | 1000     |     |
Show/hide table
( 1 ) | The parameter can be viewed only. No changes are allowed. |
( 2 ) | Calibration may be initiated from the MIDS screen or from the electronic service tool. This calibration is stored in the engine control. |
Parameters Worksheet
Note: A mistake in recording this information will result in incorrect passwords.
Show/hide table
Engine Parameters     | |
"Equipment ID"     |     |
"Engine Serial Number"     |     |
"ECM Serial Number"     |     |
"Personality Module Part Number"     |     |
Personality Module Description     |     |
"FLS"     |     |
"FTS"     |     |
"Idle Shutdown Timer"     |     |
"Shutdown Timer"     |     |
"Lighting Shutdown Timer Enable Status"     |     |
"Lighting Shutdown Timer Duration"     |     |
"Deceleration Pedal Installation Status"     |     |
"Max Deceleration Pedal Positive Engine Speed"     |     |
"Ground Speed Radar Installation Status"     |     |
"Engine Oil Weight"     |     |
"Total Tattletale"     |     |
"Engine Idle Speed"     |     |
Show/hide table
Information from Engine Information Plate     | |
"Engine Serial Number"     |     |
"FTS"     |     |
"FLS"     |     |
Note: Compare the FLS and the FTS from the ECM with the values that are listed on the Engine Information Plate. The FLS and the FTS should only be changed because of a mechanical change in the engine. The use of the wrong parameters could cause damage to the engine. The use of the wrong parameters may also void the Caterpillar warranty.
Caterpillar Information System:
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Transmission Pressures - Test
Installation Procedure for Installing a Blade on 574 Forwarders{6060} Installation Procedure for Installing a Blade on 574 Forwarders{6060}
2002/04/01 Change to Specifications Manual {1157}
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0967 - FMI 02
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0826 - FMI 04
2002/05/27 Preparation of Air Conditioner Units for Seasonal Use {7320}
Instructions for Updating the CABSDos Software and Reinstalling the CABSDos Software{7610, 7620} Instructions for Updating the CABSDos Software and Reinstalling the CABSDos Software{7610, 7620}
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0826 - FMI 03
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Transmission Charging Pump Pressure - Test
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0709 - FMI 06
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0709 - FMI 05
2002/06/24 Correction to Specifications , "Pressure Control Valve (Transmission)" {3074}
IQAN<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Monitoring ; Control System Retrieving and Saving Parameter Files
2002/04/01 New Connectors are Used on the Gear Shift Harness {1408}
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Initial Pressures - Test and Adjust
2002/06/24 Correction to Testing and Adjusting , "Transmission Hydraulic Control Primary Clutch Pressure - Test and Adjust" {3167}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Fuel Tank Water and Sediment - Drain
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Hydraulic System Pilot Valve - <B>190-6722</B> Pilot Valve
797 and 797B Off-Highway Truck Power Train Electronic Control System MID 081 - CID 0967 - FMI 09
RM-350B Reclaimer Mixer Machine Electronic Control System Propel Lever - Calibrate
2002/06/24 Correction to Testing and Adjusting , "Transmission Hydraulic Control Clutch Pressure - Test" {3167}
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Engine Supplement Fan and Piston Motor (Hydraulic Fan) - Remove
2002/06/24 Correction to Disassembly and Assembly , "Transmission Hydraulic Control - Assemble" {3167}
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Engine Supplement Fan and Piston Motor (Hydraulic Fan) - Install