Fan Group (Includes Fan, Fan Shroud, and Hydraulic Fan Motor) - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 2 |
- Install Tooling (A) to fan (12), as shown.
Show/hide table
 | |
| Illustration 1 | g00753643 |
- Attach a suitable hoist and lifting chains to Tooling (A), as shown.
- Use the hoist in order to install fan (12). The weight of fan (12) is 340 kg (750 lb).
- Install pin (13) and washer (15) .
Show/hide table
 | |
| Illustration 2 | g00753644 |
Lower Hinge | |
- Install bolt (14) and the washer.
- Repeat Steps 4 and 5 for the upper pin.
- Install latch assembly (11), the bolt, and the washer.
Show/hide table
 | |
| Illustration 3 | g00753642 |
- Connect three hose assemblies (10) .
Show/hide table
 | |
| Illustration 4 | g00753641 |
Right Side View | |
- Connect electrical connector (8) .
Show/hide table
 | |
| Illustration 5 | g00753640 |
Right Side View | |
- Install three bolts (9), the washers, and the clips.
- Attach a suitable hoist and lifting slings to cover (6), as shown.
Show/hide table
 | |
| Illustration 6 | g00753654 |
Show/hide table
 | |
| Illustration 7 | g00753653 |
- Use the hoist in order to install cover (6). The weight of cover (6) is 45 kg (100 lb).
- Install bolts (3) and (4), the spacers, and the washers finger tight.
- Remove lifting slings (5) and (7) .
- Tighten bolts (3) and (4) .
- Engage two clamps (2) .
Show/hide table
 | |
| Illustration 8 | g00751240 |
- Close access door (1) on left side of machine. Repeat this procedure for the opposite side.
Show/hide table
 | |
| Illustration 9 | g00751239 |
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect" for the machine that is being serviced.
Caterpillar Information System:
2002/05/27 A Special Instruction, REHS1228, "Field Installation of the Open Circuit Oil Breather Gp (Engine Kit)" Is Available {1058}
2002/03/01 Procedure For Cleaning Engine Bolts {1000}
CB-634D Vibratory Compactor Machine Systems Piston Pump (Drum Propel) - Remove
CB-634D Vibratory Compactor Machine Systems Piston Pump (Vibratory) - Install
CB-634D Vibratory Compactor Machine Systems Piston Pump (Vibratory) - Remove
2003/12/01 Maintaining the Mechanical Linkage Between the Engine Flywheel and the Hydrostatic Pump {3203, 5070}
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Monitoring System
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Transmission Control (Shift Lever)
834G Wheel Tractor and 836G Landfill Compactor Engine Supplement Radiator Top Tank - Install
2002/01/21 Changes to the Rear Spindle and to the Bearing Cone {4208, 4234, 7551}
CB-634D Vibratory Compactor Machine Systems Brake Pump - Remove and Install
CB-634D Vibratory Compactor Machine Systems Vibratory Valve - Install
CB-634D Vibratory Compactor Machine Systems Piston Pump (Drum Propel) - Install
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Engine Fan Control Solenoid Circuit - Test
AS2251 Screed Mix Height Control
2002/05/27 Addition to Testing and Adjusting , "Torque Converter Stall - Test" {3101}
3126B Engine for Caterpillar Built Machines Speed Sensor
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Steering Cylinder - Remove and Install
735 Articulated Truck Power Train Wheel Bearings and Duo-Cone Seals (Rear) - Install
2002/01/28 Service Spools for Backhoe Valves {5051}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Charging System
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Electronic Control Module (ECM) - Replace
CB-634D Vibratory Compactor Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Glossary of Electrical Terms