Engine Air Filter Secondary Element - Replace
Show/hide table
| NOTICE |
|---|
Always replace the secondary filter element. Never attempt to reuse it by cleaning. The secondary filter element should be replaced at the time the primary element is serviced for the third time. The secondary filter element should also be replaced if the yellow piston in the filter element indicator enters the red zone after installation of a clean primary element, or if the exhaust smoke is still black. |
- Raise the hood of the engine compartment.
Note: Refer to Operation and Maintenance Manual, "Hood Tilting" for a guide to the proper procedure for raising the hood of the machine.
- Remove the air cleaner housing cover.
Show/hide table
 | |
| Illustration 1 | g00833524 |
- Remove the primary filter element from the air cleaner housing.
Show/hide table
 | |
| Illustration 2 | g00833605 |
- Remove the secondary filter element.
Show/hide table
 | |
| Illustration 3 | g00833650 |
- Cover the air inlet opening. Clean the inside of the air cleaner housing.
Show/hide table
 | |
| Illustration 4 | g00833665 |
- Uncover the air inlet opening. Install a new secondary element.
- Install the primary filter element and the air cleaner housing cover.
- Reset the filter element indicator.
Show/hide table
 | |
| Illustration 5 | g00833441 |
- Unlatch the rod for the hood support. Close the hood for the engine compartment.
Caterpillar Information System:
CP-433C, CS-431C and CS-433C Paving Compactors Specifications
966G Series II and 972G Series II Wheel Loaders Engine Supplement Crankshaft Front Seal - Install - Engine in Chassis
TK1051 Track Feller Buncher Window (Side Sliding)
2001/11/19 New Clutch Discs with Improved Friction Material are Used for Improved Service Life {3030, 3160, 3187}
TL5 Series Field Cultivator Hydraulic Cylinders - Phasing
TL5 Series Field Cultivator Bearings - Lubricate
A Process is Available to Replace the Propel Lever Group{3209, 5462} A Process is Available to Replace the Propel Lever Group{3209, 5462}
950G Series II Wheel Loader and 962G Series II Wheel Loader Electrohydraulic System Ride Control Accumulator - Test and Charge
3408E Engine Supplement for 769D Off-Highway Trucks and 771D Off-Highway Quarry Trucks Engine and Torque Converter - Install
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0418 - FMI 05
2001/11/26 New Control Software for the Chassis ECM is Used {7620}
TL5 Series Field Cultivator Transporting the Implement
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0418 - FMI 06
CP-433C, CS-431C and CS-433C Paving Compactors Plate Locations and Film Locations
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0419 - FMI 03
TK1051 Track Feller Buncher Machine Systems Pilot Valve (Travel) - Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Machine Systems Pilot Valve (Oil Manifold) - Remove
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Gear Pump
D7R Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet)
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Relief Valve (Main) - Test and Adjust
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Steering Cylinder
CP-563C and CS-563C Vibratory Compactors Final Drive Planetary (Drum) Oil Sample - Obtain
D7R Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet)
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Steering Cylinder