Differential Pinion Preload - Adjust
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 9S-7338     | 十字挡块     | 1     |
8T-0357 | 螺栓 M16X2.0X70MM     | 3     | |
8T-1757 | 螺母 M16X2.0     | 1     | |
9X-8268 | 垫圈     | 4     | |
B     | 9U-5017     | 扭矩扳手     | 1     |
C     | 1U-6690     | 套筒扳手     | 1     |
Show/hide table
图 1 | g00589433 |
小齿轮和壳体 (1) 伞齿轮。 (2) 轴承内圈。 (3) 轴承外圈。 (4) 壳体。 (5) 轴承外圈。 (6) 轴承内圈。 (7) 垫圈。 (8) 螺母。 (A) 螺栓圆周半径。 |
注: 前齿轮组件和后齿轮组件使用同样的调整。
- 将轴承外圈 (3) 和 (5) 安装到壳体 (4) 中。 轴承外圈必须座合在壳体 (4) 的台肩上。
- 将轴承内圈 (2) 安装在小齿轮 (1) 上。 轴承外圈 (2) 必须座合在小齿轮 (1) 的台肩上。 润滑轴承内圈 (2) 。
- 将小齿轮 (1) 安装在壳体 (4) 中。 将轴承外圈 (6) 压装到轴上。 允许存在少量的轴向间隙。 润滑轴承内圈 (6) 。 润滑垫圈 (7) 和螺母 (8) ,并安装垫圈 (7) 和螺母 (8) 。
注: 如果冷冻轴承外圈,则允许这些零件到达相同的温度。 然后使用起子或压具重设轴承外圈。 冷冻轴承外圈的极限温度是 −29°C (−20°F)。 除去所有冰霜并把轴承外圈擦干。 用 SAE 30 齿轮油润滑轴承外圈,以防轴承外圈生锈。
注: 如果加热轴承内圈,则允许这些零件到达相同的温度。 然后使用起子或压具重设轴承内圈。 加热轴承内圈的最大极限温度为 135°C (275°F),最长四个小时。 轴承内圈冷却后,用 SAE 30 齿轮油润滑轴承内圈,以防轴承内圈生锈。
- 将工具 (A) 安装到小齿轮轴一端。
Show/hide table
图 2 | g01368034 |
Show/hide table
图 3 | g01368036 |
Show/hide table
图 4 | g00667185 |
- 慢慢转动小齿轮轴。 检查滚动扭矩。 新轴承正确的滚动扭矩为 1.0 N·m 至 1.7 N·m (9 lb in
至 15 lb in)。
注: 对于工作时间超过 100 小时的机器,将滚动扭矩降低至 0.5 N·m 至 0.85 N·m (4.5 lb in 至 7.5 lb in)。
- 继续拧紧固定螺母 (8) 直到扭矩扳手 (B) 上的读数与表 2 中的值相符。
Show/hide table
表 2 小齿轮滚动扭矩         小齿轮实际扭矩     新轴承    
1.0 至 1.7 N·m (9 至 15 lb in)    旧轴承    
0.5 至 0.85 N·m (4.5 至 7.5 lb in)    确保小齿轮轴 (1) 的轴向间隙为零。
- 如果小齿轮滚动扭矩超过技术规格,将螺母 (8) 旋出 1/8 圈,并重新将轴承内圈 (6) 和垫圈 (7) 座合在螺母 (8) 上。 再次执行步骤 5 和步骤 6。
- 当转动小齿轮所需的扭矩正确时,锁紧螺母 (8) 。 锁紧螺母 (8) ,将螺母上的套环敲入小齿轮轴 (1) 的键槽内。 正确尺寸参阅图 5。
注: 如果套环在拆卸或重新锁紧期间没有裂纹,则螺母可继续使用。
Show/hide table
图 5 | g00103469 |
锁紧螺母尺寸
- 尺寸 B ... 10 至 30°
- 尺寸 C ... 7.5 to 8.0 mm (.30 至 .32 in)
- 尺寸 D ... 4.7 mm (.19 in)
- 尺寸 E ... 2.5 mm (.10 in)
- 尺寸 C ... 7.5 to 8.0 mm (.30 至 .32 in)
Caterpillar Information System:
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Pilot Valve (Loader) - Install
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Window Wiper and Wiper Motor (Front) - Remove
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0562 - FMI 12
2001/02/05 Special Instructions, REHS0969, "Installation of Remote Mounting of the Air Conditioner Condenser" is Now Available {1805}
2000/12/25 Cold Weather Accessories for Skid Steer Loaders {1383, 1401, 7301, 7304, 7308, 7310}
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0562 - FMI 09
RM-250C Reclaimer Mixer Propel System Piston Motor (Transmission, Axle, and Final Drive)
2000/11/27 A New Directional Control Valve Improves the Response of the Proportional Steering on Remote Control {5412}
2001/02/05 Improved Lift Arm Bearings are Available {6107, 6118}
2001/03/12 The Hardware and Software for the Transmission have been Revised {3168, 7620}
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0562 - FMI 02
Installation Procedure for Improved Hose Routing on Harvester Heads{5051, 5057} Installation Procedure for Improved Hose Routing on Harvester Heads{5051, 5057}
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0585 - FMI 02
988G Wheel Loader Power Train Differential Backlash and Bearings - Adjust
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Tire Segment - Replace - Removal
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Pilot Valve (Loader) - Disassemble
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0590 - FMI 02
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
432D and 442D Backhoe Loaders Joystick Control (Loader)
2001/04/23 Certain Parts of the 153-8338 Air Control Valve Gp and of the 143-8994 Air Control Valve Gp are Now Available {4265, 4290}
432D and 442D Backhoe Loaders Multipurpose Controls
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0590 - FMI 09
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Loader) (Pilot Operated)
725, 730 , 730 EJECTOR, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System - AT Engine Overspeed Function