Window Wiper and Wiper Motor (Front) - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 145-5242     | Puller Group     | 1     |
Note: Put identification marks on all lines, hoses, wires, and tubes for installation purposes.
Note: The switch for the wiper motor must be in the OFF position.
Note: Remove the headliner from the cab in order to remove the window wiper motor.
- Remove cap (2) from mirror (1) .
Show/hide table
Illustration 1 | g00756730 |
- Remove nut (3) and washer (4). Remove mirror (1) .
Show/hide table
Illustration 2 | g00756736 |
- Remove four screws (5) from speaker cover (6). Remove speaker cover (6) .
Show/hide table
Illustration 3 | g00757274 |
- Remove the speaker cover on the opposite side.
- Remove four screws (7). Remove face plate opening (8) .
Show/hide table
Illustration 4 | g00757330 |
- Remove light (9) from the headliner.
Show/hide table
Illustration 5 | g00757344 |
- Disconnect two wires (10) from light (9) and remove light (9) .
Show/hide table
Illustration 6 | g00757347 |
- Remove two plastic retainers (11). Remove two plastic retainers from the opposite side.
Show/hide table
Illustration 7 | g00757348 |
- Open cap (13) on the window wiper (14) .
Show/hide table
Illustration 8 | g00757132 |
- Remove nut (12) and the washer.
- Remove tube (15) of the washer fluid bottle from window wiper blade (14) .
Show/hide table
Illustration 9 | g00757135 |
- Use tooling (A) and remove window wiper (14) .
- Remove cover (16) .
Show/hide table
Illustration 10 | g00757193 |
- Remove one nut and two washers (17) from the shaft of the window wiper motor.
Show/hide table
Illustration 11 | g00757266 |
- Remove three screws and the washers (18) .
Show/hide table
Illustration 12 | g00757270 |
- Remove wire tie-wrap (19) .
Show/hide table
Illustration 13 | g00757354 |
- Disconnect electrical connector (20) .
Show/hide table
Illustration 14 | g00757361 |
- Remove front window wiper motor (21) .
Show/hide table
Illustration 15 | g00757366 |
Caterpillar Information System:
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0562 - FMI 12
2001/02/05 Special Instructions, REHS0969, "Installation of Remote Mounting of the Air Conditioner Condenser" is Now Available {1805}
2000/12/25 Cold Weather Accessories for Skid Steer Loaders {1383, 1401, 7301, 7304, 7308, 7310}
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0562 - FMI 09
RM-250C Reclaimer Mixer Propel System Piston Motor (Transmission, Axle, and Final Drive)
2000/11/27 A New Directional Control Valve Improves the Response of the Proportional Steering on Remote Control {5412}
2001/02/05 Improved Lift Arm Bearings are Available {6107, 6118}
2001/03/12 The Hardware and Software for the Transmission have been Revised {3168, 7620}
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0562 - FMI 02
Installation Procedure for Improved Hose Routing on Harvester Heads{5051, 5057} Installation Procedure for Improved Hose Routing on Harvester Heads{5051, 5057}
2000/11/27 Revision to Specifications , "Relief Valve (Main)" and "Relief Valve (Line)" {5069, 5117}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Engine Supplement Hydraulic System Pressure - Release
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Pilot Valve (Loader) - Install
988G Wheel Loader Power Train Differential Pinion Preload - Adjust
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0585 - FMI 02
988G Wheel Loader Power Train Differential Backlash and Bearings - Adjust
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Tire Segment - Replace - Removal
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Pilot Valve (Loader) - Disassemble
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0590 - FMI 02
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
432D and 442D Backhoe Loaders Joystick Control (Loader)
2001/04/23 Certain Parts of the 153-8338 Air Control Valve Gp and of the 143-8994 Air Control Valve Gp are Now Available {4265, 4290}
432D and 442D Backhoe Loaders Multipurpose Controls
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0590 - FMI 09