Camshaft Bearings - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 129-6671 | Reaction Sleeve | 1 |
| 129-6672 | Puller Plate | 1 | |
| 129-6673 | Bearing Pilot | 1 | |
| 129-6674 | Backup Plate | 1 | |
| 6F-7032 | Bolt | 1 | |
| 1P-5542 (1) | Taperlock Stud | 1 | |
| C | 8S-2241 (2) | Camshaft Bearing Tool Group | 1 |
Show/hide table
| ( 1 ) | Part of 1P-5545 Adapter Gp |
| ( 2 ) | All of the tools that are listed above are used with Tooling (C) . |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position new camshaft bearings (1) in Tooling (A) and install the bearings from the rear to the front of the engine.
Show/hide table
 | |
| Illustration 1 | g01016694 |
Show/hide table
| NOTICE |
|---|
Location of the camshaft bearing lubrication holes is critical. Position the clinch butt joint up for all seven camshaft bearings. The No. 1 camshaft bearing oil hole is located 115 degrees counter clockwise from top center to align with the oil supply passage in the block. Camshaft bearings No. 2 through No. 7 are installed with the oil hole 45 degrees clockwise from top center. All are viewed from the front of the engine. Camshaft bearings 1,2,3,4,5, and 6 are the same width. Camshaft bearing No. 7 has a smaller width. Refer to the Specifications Manual for more information. |
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
- Install the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Caterpillar Information System:
D350E Series II and D400E Series II Articulated Trucks Hoist Cylinder Bearings - Lubricate
12H, 140H and 160H Motor Graders Engine Supplement Battery - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Remove
12H, 140H and 160H Motor Graders Machine Systems Main Frames - Connect
3056 Engine for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
527 Track-Type Skidder Machine Supplements Grapple Boom (Swing Boom) - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F006 Slip Limit Override Potentiometer - Failed Low
539 Knuckleboom Loader Hydraulic System Swing Motor
527 Track-Type Skidder Machine Supplements Grapple Boom (Swing Boom) - Remove
3056 Engine for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Engine Valve Lash and Injector Fuel Timing - Check/Adjust
3176C and 3196 Industrial Engines Camshaft Bearings - Remove
980G Wheel Loader Power Train Torque Converter
527 Track-Type Skidder Machine Supplements Grapple Jib Boom Cylinder - Remove and Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Hydraulic System Preparation for Troubleshooting
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Ground Level Shutdown Switch
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F007 Slip Limit Override Potentiometer - Failed High
Challenger 65E, Challenger 75E, Challenger 85E and Challenger 95E Agricultural Tractors Three-Point Hitch-Lubricate
776D, 777D and 777D HAA Off-Highway Truck/Tractors Steering System Shuttle Valve (Secondary Steering)
D350E Series II and D400E Series II Articulated Trucks Fuses - Replace
527 Track-Type Skidder Machine Supplements Grapple Boom Cylinder - Remove and Install
3056 Engine for Caterpillar Built Machines Water Outlet Manifold - Remove