Camshaft Bearings - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 129-6671     | Reaction Sleeve     | 1     |
129-6672 | Puller Plate     | 1     | |
129-6673 | Bearing Pilot     | 1     | |
129-6674 | Backup Plate     | 1     | |
6F-7032 | Bolt     | 1     | |
1P-5542 (1) | Taperlock Stud     | 1     | |
B     | 185-3989     | Thread Lubricant     | 1     |
C     | 8S-2241 (2)     | Camshaft Bearing Tool Group     | 1     |
Show/hide table
( 1 ) | Part of 1P-5545 Adapter Gp |
( 2 ) | All of the tools that are listed above are used with Tooling (C) . |
Start By:
- Remove the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Note:
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (A) . Apply Tooling (B) on the threads.
Show/hide table
Illustration 1 | g01016694 |
- Remove camshaft bearings (1) .
Caterpillar Information System:
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Engine Valve Lash and Injector Fuel Timing - Check/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Bearings - Install
D350E Series II and D400E Series II Articulated Trucks Hoist Cylinder Bearings - Lubricate
12H, 140H and 160H Motor Graders Engine Supplement Battery - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Remove
12H, 140H and 160H Motor Graders Machine Systems Main Frames - Connect
3056 Engine for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
527 Track-Type Skidder Machine Supplements Grapple Boom (Swing Boom) - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F006 Slip Limit Override Potentiometer - Failed Low
539 Knuckleboom Loader Hydraulic System Swing Motor
980G Wheel Loader Power Train Torque Converter
527 Track-Type Skidder Machine Supplements Grapple Jib Boom Cylinder - Remove and Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Hydraulic System Preparation for Troubleshooting
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Ground Level Shutdown Switch
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F007 Slip Limit Override Potentiometer - Failed High
Challenger 65E, Challenger 75E, Challenger 85E and Challenger 95E Agricultural Tractors Three-Point Hitch-Lubricate
776D, 777D and 777D HAA Off-Highway Truck/Tractors Steering System Shuttle Valve (Secondary Steering)
D350E Series II and D400E Series II Articulated Trucks Fuses - Replace
527 Track-Type Skidder Machine Supplements Grapple Boom Cylinder - Remove and Install
3056 Engine for Caterpillar Built Machines Water Outlet Manifold - Remove
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Hydraulic System Visual Inspection
Assembly Procedure for the Flat Floor Truck Body{7258, 7960} Assembly Procedure for the Flat Floor Truck Body{7258, 7960}