Fan Drive - Assemble
Assembly Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Group | 1 |
| B | 1P-0808 | Multipurpose Grease | - |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install bearing (4) in pulley (5) .
Show/hide table
 | |
| Illustration 1 | g01029786 |
- Install lip seal (3) with Tooling (A), as shown. Apply Tooling (B) to the lip of the seal.
- Install spacer (2) so the end with the taper is toward the inside of pulley (5) .
- Install spacer (6) and bearing (9) in the front of pulley (5) .
- Position O-ring seal (7) on the front of pulley (5). Install the pulley on shaft assembly (1) .
- Install retainer (10) and bolts (11). Tighten bolts (11) to a torque of 25 ± 6 N·m (18 ± 4 lb ft).
- Install the fan adapter on pulley (5). Tighten bolts (8) to a torque of 47 ± 9 N·m (35 ± 7 lb ft).
- Fill the fan drive with Tooling (B) .
End By: Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Install".
Caterpillar Information System:
980G Wheel Loader Power Train Trunnion Support (Oscillating Axle, Rear) - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0808 FMI 09 Interface Module (No. 8) Abnormal Update - Test
3304B and 3306B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0807 FMI 09 Interface Module (No. 7) Abnormal Update - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0806 FMI 09 Interface Module (No. 6) Abnormal Update - Test
784C and 785C Off-Highway Trucks Machine Systems Quad Gauge Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Electronic Control Module (Brake) - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0805 FMI 09 Interface Module (No. 5) Abnormal Update - Test
824G , 825G and 826G Landfill Compactor Compactor Wheel Tamping Tips - Inspect/Replace
3406E On-Highway Engine Fan Drive - Disassemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0804 FMI 09 Interface Module (No. 4) Abnormal Update - Test
D250E Series II and D300E Series II Articulated Trucks Power Train Differential and Bevel Gear (Front and Rear) - Assemble
D250E Series II and D300E Series II Articulated Trucks Machine Systems Rear Axle Stabilizer Rod - Remove and Install
3406E On-Highway Engine Fan Drive - Remove
3406E and 3456 Generator Set Engines Fan Drive - Install
527 Track-Type Skidder Power Train Final Drive
Caterpillar Monitoring System Charging System Display Mode
773D Off-Highway Truck and 775D Quarry Truck Air System and Brakes Service and Parking Brake (Rear)
793C and 793C XQ Off-Highway Trucks Hydraulic System Position Sensor (Dump Body)
793C and 793C XQ Off-Highway Trucks Hydraulic System Position Sensor (Truck Body) - Adjust
527 Track-Type Skidder Power Train Transmission Oil Pump
784C and 785C Off-Highway Trucks Machine Systems Valve (Suspension Cylinder Charging) - Install
793C and 793C XQ Off-Highway Trucks Hydraulic System General Information
572R Pipelayer Engine Supplement Precleaner - Remove and Install