Equalizer Arm - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A(1) | 9U-7536 | Lift Stand | 1 |
447-0910 | Electric Hydraulic Pump (115 V) | 1 | |
447-0911 | Electric Hydraulic Pump (230 V) | 1 | |
A | OR | ||
504-9791 | Lift Gp (60Hz)(2) | 1 | |
504-9793 | Lift Gp (50Hz)(3) | 1 | |
B | 5P-9694 | Ratchet Hoist | 1 |
C | 422-2352 | Jack Stand Gp | 2 |
Show/hide table
(1) | Use Tooling (A) or (A1) based on requirements. |
(2) | Operating-Voltage (240V-480V) |
(3) | Operating-Voltage (200V-400V) |
Start By:
- Remove the tires and rims.
- Stabilize the machine frame and axles with Tooling (A) and Tooling (C). Remove eight nuts (2) and the bolts to separate equalizer arm (1) from suspension frame mountings (3).
Show/hide table
Illustration 2 g06392332 For Tooling (A1) - Stabilize the machine frame and axles with Tooling (A1) and Tooling (C). Remove eight nuts (2) and the bolts to separate equalizer arm (1) from suspension frame mountings (3).Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Show/hide table
Illustration 3 g00513605 - Attach Tooling (B) and a nylon lifting strap to equalizer arm (1) and a lift truck. Remove three bolts (5) that secure end cap (4) to equalizer arm (1).
Show/hide table
Illustration 4 g00513631 - Use three 20 mm forcing bolts (6) to remove end cap (4) from equalizer arm (1). Use the lift truck to remove equalizer arm (1) from the machine. The weight of equalizer arm (1) is
168 kg (370 lb) .Show/hide tableIllustration 5 g00513634 - Remove two conical bushings (7) from each side of the bore that is in equalizer arm (1).
- Remove the equalizer arm from the other side of the machine by using the same procedure.
Show/hide table
Illustration 1 | g06392326 |
For Tooling (A) |
Caterpillar Information System:
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake)
554 Forwarder and 574 Forwarder Seat
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Remove
527 Track-Type Skidder Hydraulic System Oil Level - Check
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Accessing Diagnostic Information
527 Track-Type Skidder Hydraulic System Oil Filter - Replace
D250E Series II and D300E Series II Articulated Trucks Machine Systems Truck Body - Remove
554 Forwarder and 574 Forwarder Heating and Air Conditioning Control
527 Track-Type Skidder Hydraulic System Oil - Change
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
527 Track-Type Skidder Fuel Tank Cap and Strainer - Clean
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering Control
824G , 825G and 826G Landfill Compactor Caterpillar Monitoring System
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3524B Engines for Off-Highway Trucks Engine Cranks but Will Not Start
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake)
527 Track-Type Skidder Recoil Spring Compartment Oil Level - Check
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering Cylinder
527 Track-Type Skidder Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) - Inspect
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0468 FMI 04 Position Sensor (Brake Pedal) Voltage Below Normal - Test
527 Track-Type Skidder Track Pins - Inspect
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Metering Pump (HMU)
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Remove
554 Forwarder and 574 Forwarder Alternate Exit