Radiator - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
开始:
- 拆下罩(散热器)。 请参阅拆解和装配, "罩(散热器)- 拆卸和安装"。
- 拆下曲轴箱防护罩。 请参阅拆解和装配, "曲轴箱防护罩 - 拆卸和安装"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且散热器盖已经冷却到可以徒手触摸时,再慢慢拆下过滤器盖以释放压力。 冷却系统调节器含碱。 应避免它与皮肤和眼睛接触。 |
- 将散热器中的冷却液放入适当的容器中,以便随后的保存或废弃处理。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 从散热器上拆下螺栓 (2) 和夹子。
Show/hide table
图 1 | g00513659 |
Show/hide table
图 2 | g00513675 |
- 从干燥器上断开在快速接头的软管组件 (4) 。
- 从冷凝器 (3) 上拆下螺栓 (1) 。
- 由两人使用扎带将冷凝器 (3) 安放到驾驶室把手组件上。
- 拆下将管组件 (6) 固定到散热器上的螺栓 (5) 和夹子。
Show/hide table
图 3 | g00513707 |
- 定位空调贮液器 (7) 远离散热器。
- 拆下将两个前大灯固定到挡泥板组件的螺栓 (8) 。 拆卸扎带。
Show/hide table
图 4 | g00513721 |
- 在线束组件 (9) 上作识别标记,以便于安装。 断开线束组件 (9) 。 拆下前大灯 (10) 。
Show/hide table
图 5 | g00513744 |
- 对其余前大灯重复步骤 8 和 9。
- 断开线束组件 (11) 。
Show/hide table
图 6 | g00513757 |
- 拆下扎带 (12) 。
Show/hide table
图 7 | g00552215 |
- 拆下将线束组件 (14) 固定到散热器 (15) 上的扎带 (13) 。
Show/hide table
图 8 | g00513761 |
- 拆下螺栓 (16) 和风扇防护罩组件 (17) 。 将风扇防护罩组件 (17) 放在散热器一旁。
Show/hide table
图 9 | g00513765 |
- 从散热器上拆下螺栓 (18) 和阀组件 (19) 。
Show/hide table
图 10 | g00513817 |
- 松开卡箍 (20) ,然后从散热器 (15) 上拆下软管 (21) 。
Show/hide table
图 11 | g00513823 |
- 拆下将线束组件固定到散热器 (15) 上的扎带 (22) 。
Show/hide table
图 12 | g00513861 |
- 拆下将软管 (24) 固定到散热器 (15) 上的螺栓 (23) 和夹子。
Show/hide table
图 13 | g00513878 |
- 在螺栓 (25) 上做识别标记,以便于安装。 从螺塞接头 (26) 上拆下螺栓 (25) 。 降下螺塞接头 (26) 和密封垫,使其远离散热器 (15) 。
Show/hide table
图 14 | g00513885 |
- 拆下将托架 (28) 固定到散热器 (15) 上的螺栓 (27) 。 降下托架 (28) ,使其远离散热器 (15) 。
Show/hide table
图 15 | g00513911 |
- 从位于机架组件上的每个散热器支架 (31) 上拆下螺栓 (29) 和安装件组件 (30) 。
注: 如有必要,松开螺栓 (32) 以帮助拆卸螺栓 (29) 。
Show/hide table
图 16 | g00513927 |
散热器左侧 |
Show/hide table
图 17 | g00513929 |
散热器右侧 |
- 将工具 (A) 和适当的起吊设备连接到散热器 (15) 。 散热器 (15) 的重量约为 370 kg (815 lb)。
Show/hide table
图 18 | g00513930 |
- 从支架上拆下螺栓和盖 (33) 。
- 如有必要,在机器的每一册从支架 (35) 上拆下螺栓 (34) 。
Show/hide table
图 19 | g00513931 |
散热器左前侧 |
Show/hide table
图 20 | g00513932 |
散热器右前侧 |
- 从档板组件 (37) 上拆下螺栓 (36) 。 从机架上拆下挡板组件 (37) 。
Show/hide table
图 21 | g00513933 |
- 从机器上拆下散热器。
Caterpillar Information System:
527 Track-Type Skidder Hydraulic System Oil Level - Check
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Accessing Diagnostic Information
527 Track-Type Skidder Hydraulic System Oil Filter - Replace
D250E Series II and D300E Series II Articulated Trucks Machine Systems Truck Body - Remove
554 Forwarder and 574 Forwarder Heating and Air Conditioning Control
527 Track-Type Skidder Hydraulic System Oil - Change
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
527 Track-Type Skidder Fuel Tank Cap and Strainer - Clean
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering Control
D250E Series II and D300E Series II Articulated Trucks Power Train Solenoid Valve (Differential Lock) - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0468 FMI 03 Position Sensor (Brake Pedal) Voltage Above Normal - Test
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Center Arm (Steering) - Remove and Install
554 Forwarder and 574 Forwarder Seat
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake)
D250E Series II and D300E Series II Articulated Trucks Machine Systems Equalizer Arm - Remove
824G , 825G and 826G Landfill Compactor Caterpillar Monitoring System
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3524B Engines for Off-Highway Trucks Engine Cranks but Will Not Start
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake)
527 Track-Type Skidder Recoil Spring Compartment Oil Level - Check
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering Cylinder
527 Track-Type Skidder Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) - Inspect
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0468 FMI 04 Position Sensor (Brake Pedal) Voltage Below Normal - Test
527 Track-Type Skidder Track Pins - Inspect