Hydraulic System Oil Filter - Replace
Show/hide table
 | |
| Ilustrasi 1 | g00513567 |
- Buka baut pada engsel di penyaring(bila terpasang). Buka penyaring dan lepaskan penyaring dari alat berat. Lepas tutup pengisian oli secara perlahan untuk mengeluarkan tekanan tangki. Lepaskan mur penahan.
- Lepaskan penutup rumah filter dan susunan filter.
Show/hide table
 | |
| Ilustrasi 2 | g00513577 |
- Lepas elemen filter. Buang elemen filter.
- Jika stud dilepaskan selama pelepasan mur penahan, stud nanti perlu dipasang kembali. Kencangkan stud dengan torsi 55 ± 7 N·m (40 ± 5 lb ft).
- Lepaskan retainer ring dan penyaring dari pipa pengisian oli.
- Bersihkan penyaring dan penutup dalam pelarut yang bersih dan tidak mudah terbakar.
- Pasang elemen filter yang baru dan penutupnya.
- Pasang mur penahan.
- Lepaskan penutup akses dan elemen filter oli untuk pompa attachment (bila terpasang). Buang elemen filter.
- Pastikan semua seal lama telah diambil dari dudukan filter.
- Lumasi secara tipis-tipis oli engine bersih ke seal filter baru.
- Pasang filter yang baru dengan tangan hingga seal filter menyentuh dudukan. Kencangkan filter dengan 3/4 putaran tambahan. Tersedia tanda indeks rotasi di filter yang baru dengan jarak 90 derajat. Gunakan tanda indeks sebagai acuan dalam mengencangkan filter.
- Periksa seal di penutup dan bagian atas tangki. Pasang seal yang baru jika seal lama rusak.
- Pasang penutup dan susunan filter.
- Pasang saringan, ring penahan, dan tutup.
- Geser penyaring ke engsel. Tutup penyaring dan kencangkan baut.
- Pertahankan tingkat oli hidrolik pada tanda "PENUH" di meteran pengamat.
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Machine Systems Truck Body - Remove
554 Forwarder and 574 Forwarder Heating and Air Conditioning Control
527 Track-Type Skidder Hydraulic System Oil - Change
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
527 Track-Type Skidder Fuel Tank Cap and Strainer - Clean
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering Control
D250E Series II and D300E Series II Articulated Trucks Power Train Solenoid Valve (Differential Lock) - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0468 FMI 03 Position Sensor (Brake Pedal) Voltage Above Normal - Test
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Center Arm (Steering) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Check Valve (Double) - Disassemble
784C and 785C Off-Highway Trucks Machine Systems Check Valve (Double) - Assemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Electric Drive Pump (Secondary Steering)
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Accessing Diagnostic Information
527 Track-Type Skidder Hydraulic System Oil Level - Check
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Remove
554 Forwarder and 574 Forwarder Seat
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake)
D250E Series II and D300E Series II Articulated Trucks Machine Systems Equalizer Arm - Remove
824G , 825G and 826G Landfill Compactor Caterpillar Monitoring System
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3524B Engines for Off-Highway Trucks Engine Cranks but Will Not Start
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake)
527 Track-Type Skidder Recoil Spring Compartment Oil Level - Check
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering Cylinder