Drain Holes May Be Missing On Left Hand Side (LHS) Bumper Tool Box Caterpillar


Drain Holes May Be Missing On Left Hand Side (LHS) Bumper Tool Box

Usage:

WHEEL LOADERS826G (7LN) LANDFILL COMPACTOR

Problem:

The three drain holes that should be present in the left hand side (LHS) bumper tool box (Illustration 1) of the landfill compactor listed may be missing. Water stagnation in the LHS bumper tool box may result.

Solution:

Use the following rework procedure to prevent the water from stagnating in the LHS bumper tool box of the 826G (7LN) Landfill Compactor.

1. Machine three holes of 25.0 mm (.98 in) diameter in the base plate of the LHS bumper tool box. See Illustration 2 for recommended locations of the three new holes.

NOTE: The exact location of the holes drilled in the base plate is not critical.

2. Grind away any burrs or sharp edges resulting from the machining of the new holes.
3. Paint the new hole area with a rust inhibitor.


Illustration 1 - The LHS Bumper Tool Box


Illustration 2 - Recommended locations for the three new drain holes in the LHS Bumper Tool Box (1)

COPYRIGHT 1996 CATERPILLAR ALL RIGHTS RESERVED

Caterpillar Information System:

Aftercooler Core Cracks Aftercooler Core Cracks
Rear Propel Pump Interlock Solenoid Wires May Break Rear Propel Pump Interlock Solenoid Wires May Break
Contact For Ordering FT-Drawings Contact For Ordering FT-Drawings
Nuts Holding The Weight Group To The Compactor Drum May Not Be Sufficiently Tight Nuts Holding The Weight Group To The Compactor Drum May Not Be Sufficiently Tight
Trims May Loosen On The Rear Of The 820G And 980G Cabs Trims May Loosen On The Rear Of The 820G And 980G Cabs
Limiting Hydraulic Oil Flow When Using Auxiliary Valves Limiting Hydraulic Oil Flow When Using Auxiliary Valves
Idler/Bogie Roller Bearings May Not Be Correct Idler/Bogie Roller Bearings May Not Be Correct
Procedure To Repair Weld Joint Cracks On Lift Arms Procedure To Repair Weld Joint Cracks On Lift Arms
Ride Control Switch Ride Control Switch
Ride Control System On Medium Wheel Loaders Built At Caterpillar Beglium Ride Control System On Medium Wheel Loaders Built At Caterpillar Beglium
New Stabilizer Foot New Stabilizer Foot
Mechanical Hoe Quick Coupler Mechanical Hoe Quick Coupler
Air Filter Precleaner Modification Can Increase Filter Element Life Air Filter Precleaner Modification Can Increase Filter Element Life
Loss Of Modulation May Occur On Some Motor Graders Loss Of Modulation May Occur On Some Motor Graders
Water Leaks Into Cab Through The Roof Seal Water Leaks Into Cab Through The Roof Seal
Regulate Oil Flow For Supplier Attachments Regulate Oil Flow For Supplier Attachments
Change Oil In Any Flexxaire Fan With Serial Number Below 3000 Or JS3000 Change Oil In Any Flexxaire Fan With Serial Number Below 3000 Or JS3000
New Design Of The Rear View Mirror Support Has Been Released For The FII-Cab Of Medium Wheel Loaders New Design Of The Rear View Mirror Support Has Been Released For The FII-Cab Of Medium Wheel Loaders
Automatic Transmission Fluid (ATF) Is Not An Acceptable Lubricant For Flexxaire Fans With Serial Numbers Below 3000 Or JS3000 Automatic Transmission Fluid (ATF) Is Not An Acceptable Lubricant For Flexxaire Fans With Serial Numbers Below 3000 Or JS3000
Unused Electrical Harness Wires Need To Be Covered Unused Electrical Harness Wires Need To Be Covered
Technical Support Available For Paint Defects In Aurora Built Machines Technical Support Available For Paint Defects In Aurora Built Machines
Corrected Information Provided For 7J-5311 Warning Plate On Certain Medium Wheel Loaders And Integrated Toolcarriers Equipped With Ride Control Corrected Information Provided For 7J-5311 Warning Plate On Certain Medium Wheel Loaders And Integrated Toolcarriers Equipped With Ride Control
Casting Irregularities In Some 105-8698 Axle Housings And 105-8699 Axle Housings May Allow Oil Seepage In Certain Areas Of The Axle Housing Casting Irregularities In Some 105-8698 Axle Housings And 105-8699 Axle Housings May Allow Oil Seepage In Certain Areas Of The Axle Housing
Special Care Necessary For Proper Alignment Of Brake Pumps During Pump Group Disassembly And Assembly Special Care Necessary For Proper Alignment Of Brake Pumps During Pump Group Disassembly And Assembly
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.