1994/02/28 Caterpillar

Improved Lubrication Of Attachment Coupler Bushing {5133}

Usage:

All Telescopic Material Handlers

Description of Change: Current production machines have grease fittings installed in the bosses which support the attachment coupler pivot shaft in the boom head. The bosses are equipped with self lubricating type bushings, but in some applications, dirt enters and shortens the bushing service life. Installation of these grease fittings on machines that do not have them will allow for improved lubrication of the attachment coupler bushings

Adaptable To: This change is adaptable to all machines in service if required. Two 3B8489 Grease Fittings are required.

Installation Procedure

1. Remove the attachment coupler.

2. Drill 8.5 mm (.33 in) hole (A) through each boss and bushing at the positions indicated in the illustration. Tap holes with 1/8NPTF and install the 3B8489 Grease Fittings.

3. Assemble the attachment coupler to the boom head and lubricate all fittings.

4. Subsequent lubrication should be at the existing attachment coupler fittings interval of 50 service hours or two weeks.

Caterpillar Information System:

1994/02/28 New Guard And Skirting Added To Cutter Box To Protect Tail Pulley And Lower Portion Of First Stage Conveyor {6635}

1994/02/28 6G-2943 Circle Assembly Can Be Reinforced To Improve Service Life In Severe Applications {6154,6157}

1994/02/28 New Resistor Provides Higher Intermediate Speed of Air Conditioner Fan {7320,7337}

1994/02/28 Implement Status Switch Harness Modifications {1408,7490}

1994/02/28 Fuel Sump Tank Drain Valve Protection Available {1279}

1994/02/28 New Shroud Assembly Now Available for Power Take Off {1165}

1994/02/21 Servicing Lighted Rocker Switches {1435}

1994/02/21 Performance Of Rotor Axle Seal Depends On Correct Shimming Procedure {5634}

1994/02/21 Direction Of Drum Rotation Can Be Changed; Chain Case Hub Must Be Shimmed Correctly {5634}

1994/02/21 Usage of Transmission Hand Controls {3168}

1994/02/21 Improved Screen Used In The Brake Oil Cooler {1366,4295}

1994/02/21 New Suspension Cylinder Rod Seals For Arctic Region Applications {7201,7213}

1994/02/28 Soldering Iron Available For Field Use {0709,1400}

1994/02/28 New Retaining Compound Is Available {0649}

1994/02/28 A New Gauge Group Is Now Used To Prevent Fogging {7450}

1994/02/28 Identification Plate For Starting/Charging Diagnostic Connector {1450,7557,7569}

1994/02/28 New Turbocharger Models Have Left-Hand Threads On Compressor Nut And Turbine Shaft {1053,1052}

1994/02/28 Remove Internal Components From 4P-8454 Cover Assembly {1309}

1994/02/28 Non-Counterbored Valve Guides Used To Reduce The Amount Of Oil That Flows Down Valve Stem {1104}

1994/02/28 Improved 1R-0716 Oil Filter Should Be Used On 3500 Engines {1318}

1994/03/07 Circle Drive Unit Cover Can Be Modified To Prevent Oil Loss Through The Vent{5201,5209}

1994/03/07 Boss Needed To Mount Replaced Fuel Tank{1273}

1994/03/07 Front Axle Toe-In Adjustment Procedure{4313}

1994/03/07 New Parts Service Thrust Washers, Planet Gears And Sun Gear Improve Final Drive Service Life {4055,4051}