Water Pumps In Parts Stock Need To Have The Coolant Seals Replaced And Certain Seals Need To Be Removed From Stock Caterpillar

Water Pumps In Parts Stock Need To Have The Coolant Seals Replaced And Certain Seals Need To Be Removed From Stock

Usage:

@media screen { div.divFooter { display: none; } } @media print { div.divFooter { position: fixed; bottom: 0; right: 0; } }

Caterpillar: Confidential Yellow

NOTE: The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

NOTE: Mail Code U-108 was used on both the July 21, 1994 and the July 22, 1994 Service Letters.When filing your Service Letters, make sure both letters are accounted for.

NOTE: This Revised Service Letter replaces the July 22, 1994 Service Letter. Changes have been made to explain Mail Code U-108.

Termination Date

October 31, 1994

Problem

Certain water pumps in Parts Stock for use on 3300 and 3400 Engines need to have the coolant seal groups replaced. Certain water pump coolant seal groups need to be removed from Parts Stock.

Action Required

Remove all 106-7150 Seals (Chg 01) from Parts Stock.

NOTE: It is not necessary to remove any of the former 106-7150 Seals manufactured to Change 00. 106-7150 Seals manufactured to Change 00 can be used for this rework.

Inspect the following water pumps in Parts Stock for a date code of 2-94 through 5-94 (NMDR, NEDR, DRDR, and NADR). The date code should be located next to the part number.

If the water pumps have one of these date codes, refer to Special Instruction SEHS8449 or the system operation, test and adjust section of the Service Manual to change the coolant seal.

Remove the impeller and the rotating portion of the existing coolant Seal (Chg 01). Leave the stationary portion of the coolant seal in place to simplify the repair. Install the rotating portion of the new 118-9163 Coolant Seal. After lubricating the shaft with clean water or coolant, use the 2W9102 Installation Tool to push the rotating portion of the seal onto the shaft. Install the spring and impeller. Tighten the impeller bolt to a torque of 39 ± 3 N·m (28 ± ft. lb.).

NOTE: The rotating portion of a the former 106-7150 Chg 00 Coolant Seal can also be used if there are any in dealer Parts Stock. Reuse the spring from the Parts Stock water pump if a 106-7150 Chg2000 Coolant Seal is used.

Service Claim Allowances

Submit one claim for all water pumps from Parts Stock that were reworked and for all 106-7150 (Chg 01) Seals that were removed from Parts Stock. Claim .3 hours of labor the dealer cost rate for each water pump reworked.

Parts Disposition

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

Caterpillar Information System:

Product Support Program For Replacing The Personality Module Installed On Certain 3408 Marine High Performance Engines Product Support Program For Replacing The Personality Module Installed On Certain 3408 Marine High Performance Engines

Product Support Program For Replacing The Fuel Injector Nozzles On Certain 3406C Engines Rated At 415 Or 425 Horsepower Product Support Program For Replacing The Fuel Injector Nozzles On Certain 3406C Engines Rated At 415 Or 425 Horsepower

The Exhaust Valve Springs Need To Be Replaced On Certain 3116 Truck Engines And 938F And 960 Loaders The Exhaust Valve Springs Need To Be Replaced On Certain 3116 Truck Engines And 938F And 960 Loaders

Product Support Program For Installing And Calibrating A New Oil Level Gage On Certain 3406B PEEC And 3406C Electronic Engines Equipped With A Front-Sump Oil Pan Product Support Program For Installing And Calibrating A New Oil Level Gage On Certain 3406B PEEC And 3406C Electronic Engines Equipped With A Front-Sump Oil Pan

Service Letter Cancellation Service Letter Cancellation

The Turbocharger Compressor Housing Bolts Need To Be Changed On Certain 3606, 3608, 3612 And 3616 Engines The Turbocharger Compressor Housing Bolts Need To Be Changed On Certain 3606, 3608, 3612 And 3616 Engines

Certain Fuel Injectors Need To Be Removed From Part Stock Certain Fuel Injectors Need To Be Removed From Part Stock

Product Support Program For Installing A New Turbocharger And Fuel Injector Nozzles On Certain 435 Hp 3208 TA Marine Engines Product Support Program For Installing A New Turbocharger And Fuel Injector Nozzles On Certain 435 Hp 3208 TA Marine Engines

A Plug May Need To Be Replaced In The Auxiliary Sea Water Pump On Certain 3408 And 3412 Marine Engines A Plug May Need To Be Replaced In The Auxiliary Sea Water Pump On Certain 3408 And 3412 Marine Engines

Product Support Program For Updating The Electronic Control Group (Personality Module) On Certain 3176B And 3406E Truck Engines Product Support Program For Updating The Electronic Control Group (Personality Module) On Certain 3176B And 3406E Truck Engines

The Seawater Aftercooler Core Assembly Needs To Be Replaced On Certain 3208 Marine Engines The Seawater Aftercooler Core Assembly Needs To Be Replaced On Certain 3208 Marine Engines

Certain 0R3839 And 0R3840 Remanufactured Cylinder Heads Used For G3500 Engines Need To Be Inspected To Determine If A 4P6925 Oil Sleeve Has Been Installed In The Center Cam Follower Bore Certain 0R3839 And 0R3840 Remanufactured Cylinder Heads Used For G3500 Engines Need To Be Inspected To Determine If A 4P6925 Oil Sleeve Has Been Installed In The Center Cam Follower Bore

Replace The Piston Oil Cooling Tubes On Certain 3408B And 3408C Marine Engines Replace The Piston Oil Cooling Tubes On Certain 3408B And 3408C Marine Engines

Product Support Program For Installing Flexible Conduit On The Wiring Harness On Certain 3408 And 3412 Marine Engines Product Support Program For Installing Flexible Conduit On The Wiring Harness On Certain 3408 And 3412 Marine Engines

Remove All 3E6777 Seals And 5P8057 Kits From Dealer Inventory Remove All 3E6777 Seals And 5P8057 Kits From Dealer Inventory

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

Remove All 7N9331, 7N9335, And 8N1911 Gaskets From Parts Stock Remove All 7N9331, 7N9335, And 8N1911 Gaskets From Parts Stock

Product Support Program For Reworking Certain 3406C Truck Engines With Low Power Complaints Product Support Program For Reworking Certain 3406C Truck Engines With Low Power Complaints

Certain Remanufactured Crankshafts For Use In 3412 Engines Need To Be Removed From Parts Stock Certain Remanufactured Crankshafts For Use In 3412 Engines Need To Be Removed From Parts Stock

The 4P5437 Gear Shaft In The Rear Gear Train Needs To Be Inspected For Debris On Certain 3508, 3512, 3516, G3508, G3512 and G3516 Engines The 4P5437 Gear Shaft In The Rear Gear Train Needs To Be Inspected For Debris On Certain 3508, 3512, 3516, G3508, G3512 and G3516 Engines

Product Support Program For Reworking The Ignition Wires On Certain G3306, G3408 And G3412 Engines Product Support Program For Reworking The Ignition Wires On Certain G3306, G3408 And G3412 Engines

Remove All 1105146 Damper Assemblies From Parts Stock Remove All 1105146 Damper Assemblies From Parts Stock

Certain 1R0751 Fuel Filters Need To Be Removed From Parts Stock And From Machines In Dealer Inventory Equipped With 3114 And 3116 Engines Certain 1R0751 Fuel Filters Need To Be Removed From Parts Stock And From Machines In Dealer Inventory Equipped With 3114 And 3116 Engines

Product Support Program For Replacing The Front Gear Train On Certain 3208 Industrial Engines Used Primarily In Fertilizer Spreader Applications Product Support Program For Replacing The Front Gear Train On Certain 3208 Industrial Engines Used Primarily In Fertilizer Spreader Applications