Wheel Lean Arm and Axle Bushings - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-1832 | Adapter | 1 |
6V-3160 | Double Acting Cylinder | 1 | |
9U-6833 | Nut | 1 | |
5P-4776 | Tool Stud | 1 | |
5P-8250 | Washer | 1 | |
350-7768 | Electric Hydraulic Pump Gp | 1 |
Start By:
- Remove the wheel lean bar.
- Remove the wheel spindle and wheel spindle housing.
Show/hide table
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
- Remove bolt (1) and retainer (3).
- Remove pin (2).
Show/hide table
Illustration 2 g06355345 Show/hide tableIllustration 3 g06355348 - Attach suitable lifting device to arm assembly (8). The weight of arm assembly (8) is approximately
29 kg (64 lb) . - Remove bolt (5) and lock (6).
- Remove bolt (4) and pin (7). Remove arm assembly (8).
Show/hide table
Illustration 4 g06355349 - Remove seals (9).
Show/hide table
Illustration 5 g06355355 - Use Tooling (A) to remove bearings (10). Remove bearings (10).
Show/hide table
Illustration 1 | g06355344 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-1832 | Adapter | 1 |
6V-3160 | Double Acting Cylinder | 1 | |
9U-6833 | Nut | 1 | |
5P-4776 | Tool Stud | 1 | |
5P-8250 | Washer | 1 | |
350-7768 | Electric Hydraulic Pump Gp | 1 | |
B | 1P-0510 | Driver Gp | 1 |
- Use Tooling (A) to install bearings (10). Install bearings (10). Install bearings (10) to a dimension of
7.2 ± 0.4 mm (0.28 ± 0.02 inch) below the inside face of the axle.Show/hide tableIllustration 7 g06355349 - Use Tooling (B) to install seals (9). Install seals (9).
Show/hide table
Illustration 8 g06355348 Show/hide tableIllustration 9 g06355345 - Attach suitable lifting device to arm assembly (8). The weight of arm assembly (8) is approximately
29 kg (64 lb) . Install arm assembly (8). - Install pin (7) and bolt (4).
- Install lock (6) and bolt (5).
Show/hide table
Illustration 10 g06355344 - Install pin (2). Install retainer (3) and bolt (1).
Show/hide table
Illustration 6 | g06355355 |
End By:
- Install the wheel spindle and wheel spindle housing.
- Install the wheel lean bar.
Caterpillar Information System:
797F Tier 4 Off-Highway Truck Field Assembly Guards - Install - Front
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Machine System Engine Control
A New Special Instruction for Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems is Now Available {7606} A New Special Instruction for Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems is Now Available {7606}
Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems {7606} Installation Procedure to Retrofit a PL321VSR Electronic Control Module (ECM) With a Pro Product Link PL641 or PL631 or PL542 Systems {7606}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Turbocharger - Remove and Install
NEHS0858 - Using the 197-5589 Wheel Stud Remover/Installer {0374, 0599, 0700, 0730, 4210} NEHS0858 - Using the 197-5589 Wheel Stud Remover/Installer {0374, 0599, 0700, 0730, 4210}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Alternator - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Battery - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Machine System Joystick Control
New Grommets Improve Support for Travel Lines on Certain 320, 320 GC, and 323 Excavators {5057, 5058} New Grommets Improve Support for Travel Lines on Certain 320, 320 GC, and 323 Excavators {5057, 5058}
Procedure to Install High-Pressure Fuel Pump on Certain 797F Off-Highway Truck Engines {1255, 1256} Procedure to Install High-Pressure Fuel Pump on Certain 797F Off-Highway Truck Engines {1255, 1256}
Reuse and Salvage Guideline for Cracks in Hydraulic Cylinder Rod Assemblies {0599, 0738, 5102, 7562} Reuse and Salvage Guideline for Cracks in Hydraulic Cylinder Rod Assemblies {0599, 0738, 5102, 7562}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Fuel Filter and Base - Remove and Install
Generator Lid May Contact Circuit Breaker on Certain C4.4 Generator Set Engines {4460} Generator Lid May Contact Circuit Breaker on Certain C4.4 Generator Set Engines {4460}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Fan and Fan Drive - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Refrigerant Compressor - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Diagnostic Trouble Codes
Check the Fuel Priming Pump Wiring Harness Connectors On Certain C9.3B Engines {1258, 1408} Check the Fuel Priming Pump Wiring Harness Connectors On Certain C9.3B Engines {1258, 1408}
C9.3B Industrial Engines Turbocharger - Remove
A New Exhaust Gasket is Now Used on Certain 3412 Engines {1059} A New Exhaust Gasket is Now Used on Certain 3412 Engines {1059}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Determining Diagnostic Trouble Codes
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Event Codes
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Refrigerant Condenser - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavator Engine Supplement Hood - Remove and Install