Side Plate - Remove and Install - Left Hand
Start By:
- Remove the rotor drive belt guard.
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 422-5474 | Lifting Eye Assembly | 2 |
- Fully lower the left-hand side plate. Refer to Operation & Maintenance Manual, "Operator Controls" , Left Side Plate Raise/Hold and Lower/Float
- Lower the machine until the bottom edge of the left-hand side plate touches the ground. Refer to Operation & Maintenance Manual, "Operator Controls" , All Leg Raise/Lower and Auto Leveling
- Remove the left rear side plate hydraulic cylinder.
- Remove the left front side plate hydraulic cylinder.
Show/hide table
Illustration 1 g06131700 - Remove six bolts (1). Repeat process for opposite side of ladder (2). Remove ladder (2).
Show/hide table
Illustration 2 g06131751 Show/hide tableIllustration 3 g06131776 - Remove two bolts (3) and replace with tooling (A) to support the weight of left-hand side plate (4). The weight of left-hand side plate (4) is approximately
230 kg (507 lb) Show/hide tableIllustration 4 g06131764 - Remove four bolts (4). With the assistance of another person, remove guide assembly (5). The weight of guide assembly (5) is approximately
40 kg (88 lb) Show/hide tableIllustration 5 g06131784 - Remove two bolts (8) and backing plate (7).
Show/hide table
Illustration 6 g06131791 - Remove left-hand side plate (4).
- Install left-hand side plate (4) in the reverse order of removal.
Caterpillar Information System:
G3512 Generator Set Engine Aftercooler - Disassemble
A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258} A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100}
C175 Oil&Gas Offshore Engine Circuit Breaker - Test
New Software Is Used on Certain C9 and C13 Engines {1920} New Software Is Used on Certain C9 and C13 Engines {1920}
C175 Oil&Gas Offshore Engine Electrical Power Supply - Test
3600 Heavy Fuel Engines Engine Operation
Photovoltaic Inverters Reference Material
3512B Generator Set Engines with Dynamic Gas Blending Injector Solenoid - Test
G3500H Generator Set Engine Fuel Differential Pressure Is High
3516B Generator Set Engines with Dynamic Gas Blending Electrical Power Supply - Test
3516B Generator Set Engines with Dynamic Gas Blending Sensor Signal (Analog, Passive) - Test
Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408} Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216}
Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408} Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408}
G3512 Generator Set Engine Aftercooler - Assemble
320D3 and 323D3 Excavators Machine System Specifications Boom - 5.7 m (18.70 ft)
349F and 352F Excavators Machine System Specifications Piston Pump
320D3 and 323D3 Excavators Machine System Specifications Bucket Cylinder
C175 Oil&Gas Offshore Engine Engine Cranks but Does Not Start
G3512 Generator Set Engine Water Temperature Regulators - Remove
3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure Problem - Gas System
3516B Generator Set Engines with Dynamic Gas Blending Fuel Metering Valve - Test
C175 Oil&Gas Offshore Engine Coolant Temperature Is High