Aftercooler - Disassemble
Start By:
- Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove".
Note: Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove 29 bolts (2) to remove housing (1).
- Attach a suitable lifting device to housing (4). Housing (4) weighs approximately
26.1 kg (7.6 lb.) . - Remove 27 bolts (3) to remove housing (4).
Show/hide table
Illustration 2 g06131622 - Remove 23 bolts (6) on top and sides of after cooler to remove the top of the housing (5). Leave the bottom plates in tact.
- Inspect core for damage or blockage by foreign matter.
Show/hide table
| |
| Illustration 1 | g06131594 |
Caterpillar Information System:
A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258} A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100}
C175 Oil&Gas Offshore Engine Circuit Breaker - Test
New Software Is Used on Certain C9 and C13 Engines {1920} New Software Is Used on Certain C9 and C13 Engines {1920}
C175 Oil&Gas Offshore Engine Electrical Power Supply - Test
3600 Heavy Fuel Engines Engine Operation
Photovoltaic Inverters Reference Material
3512B Generator Set Engines with Dynamic Gas Blending Injector Solenoid - Test
G3500H Generator Set Engine Fuel Differential Pressure Is High
3516B Generator Set Engines with Dynamic Gas Blending Electrical Power Supply - Test
3516B Generator Set Engines with Dynamic Gas Blending Sensor Signal (Analog, Passive) - Test
3516B Generator Set Engines with Dynamic Gas Blending Sensor Signal (Analog, Active) - Test
PM820, PM822, and PM825 Cold Planer Machine Systems Side Plate - Remove and Install - Left Hand
Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408} Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216}
Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408} Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408}
G3512 Generator Set Engine Aftercooler - Assemble
320D3 and 323D3 Excavators Machine System Specifications Boom - 5.7 m (18.70 ft)
349F and 352F Excavators Machine System Specifications Piston Pump
320D3 and 323D3 Excavators Machine System Specifications Bucket Cylinder
C175 Oil&Gas Offshore Engine Engine Cranks but Does Not Start
G3512 Generator Set Engine Water Temperature Regulators - Remove
3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure Problem - Gas System
3516B Generator Set Engines with Dynamic Gas Blending Fuel Metering Valve - Test