A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258}
- Off-Highway Truck/Tractor
- 797 (S/N: 5YW1-UP)
- 797B (S/N: JSM1-UP)
- 797F (S/N: LAJ621-UP; WSP130-UP; LTZ1-UP)
- 797B (S/N: JSM1-UP)
Description Of Change: A new bracket has improved spacing for the transmission output speed sensor, thus allowing the ECM to detect proper machine direction. This improved bracket design also eliminates the false diagnostic codes (CID 585 - FMI 7 & CID 673 - FMI 7) from being logged.
Adaptable To: The following part is adaptable to the machines within the listed serial numbers, and is effective with all machines after the listed serial numbers.
The new bracket and former bracket part numbers are listed in Table 1.
Show/hide table
Qty | New Part Number | Former Part Number | Description |
1 | Bracket |
Caterpillar Information System:
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100}
C175 Oil&Gas Offshore Engine Circuit Breaker - Test
New Software Is Used on Certain C9 and C13 Engines {1920} New Software Is Used on Certain C9 and C13 Engines {1920}
C175 Oil&Gas Offshore Engine Electrical Power Supply - Test
3600 Heavy Fuel Engines Engine Operation
Photovoltaic Inverters Reference Material
3512B Generator Set Engines with Dynamic Gas Blending Injector Solenoid - Test
G3500H Generator Set Engine Fuel Differential Pressure Is High
3516B Generator Set Engines with Dynamic Gas Blending Electrical Power Supply - Test
3516B Generator Set Engines with Dynamic Gas Blending Sensor Signal (Analog, Passive) - Test
3516B Generator Set Engines with Dynamic Gas Blending Sensor Signal (Analog, Active) - Test
C175 Oil&Gas Offshore Engine Clean Fuel Module - Test
G3512 Generator Set Engine Aftercooler - Disassemble
PM820, PM822, and PM825 Cold Planer Machine Systems Side Plate - Remove and Install - Left Hand
Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408} Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216}
Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408} Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408}
G3512 Generator Set Engine Aftercooler - Assemble
320D3 and 323D3 Excavators Machine System Specifications Boom - 5.7 m (18.70 ft)
349F and 352F Excavators Machine System Specifications Piston Pump
320D3 and 323D3 Excavators Machine System Specifications Bucket Cylinder
C175 Oil&Gas Offshore Engine Engine Cranks but Does Not Start
G3512 Generator Set Engine Water Temperature Regulators - Remove
3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure Problem - Gas System