G3512 Generator Set Engine Caterpillar


Aftercooler - Assemble

Usage:

G3512 E26

Assembly Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g06131622

  1. Position housing (5) and install bolts (6).

    Tighten bolts (6) to a torque of 47 ± 94 N·m (35 ± 7 lb ft).



    Illustration 2g06131594

  2. Attach a suitable lifting device to housing (4). Housing (4) weighs approximately 26.1 kg (7.6 lb.).

  3. Position housing (4) and install 27 bolts.

    Tighten bolts (6) to a torque of 47 ± 94 N·m (35 ± 7 lb ft).

  4. Position housing (2) and install 29 bolts.

    Tighten bolts (6) to a torque of 47 ± 94 N·m (35 ± 7 lb ft).

Caterpillar Information System:

Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408} Special Instruction, "Instructions for Installing Connector Lock Wires on Off-Highway Trucks" is Now Available {1401, 1402, 1408}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated to Aid in Identifying Cause of Liner Cuff Cracking Certain C175 Generator Set Engines {1000, 1216}
Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408} Instructions for Installing Connector Lock Wires on Off-Highway Trucks {1401, 1402, 1408}
PM820, PM822, and PM825 Cold Planer Machine Systems Side Plate - Remove and Install - Left Hand
G3512 Generator Set Engine Aftercooler - Disassemble
A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258} A New Transmission Output Speed Sensor Mounting Bracket is Now Used on Certain 797F Large Off-Highway Truck {1408, 1439, 3160, 3175, 3258}
Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100} Applied Failure Analysis and Reuse & Salvage Publications Have Been Updated To Aid in Identifying Cause of Inlet Valve Radial Crack on Certain C175 Engines {1100}
C175 Oil&Gas Offshore Engine Circuit Breaker - Test
New Software Is Used on Certain C9 and C13 Engines {1920} New Software Is Used on Certain C9 and C13 Engines {1920}
C175 Oil&Gas Offshore Engine Electrical Power Supply - Test
3600 Heavy Fuel Engines Engine Operation
Photovoltaic Inverters Reference Material
320D3 and 323D3 Excavators Machine System Specifications Boom - 5.7 m (18.70 ft)
349F and 352F Excavators Machine System Specifications Piston Pump
320D3 and 323D3 Excavators Machine System Specifications Bucket Cylinder
C175 Oil&Gas Offshore Engine Engine Cranks but Does Not Start
G3512 Generator Set Engine Water Temperature Regulators - Remove
3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure Problem - Gas System
3516B Generator Set Engines with Dynamic Gas Blending Fuel Metering Valve - Test
C175 Oil&Gas Offshore Engine Coolant Temperature Is High
G3512 Generator Set Engine Water Temperature Regulators - Install
C175 Oil&Gas Offshore Engine Emergency Stop - Test
C175 Oil&Gas Offshore Engine Engine Control Switch - Test
G3500H Generator Set Engine Data Link - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.