Gear Group (Rear) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Group | 1 |
Start By:
- Remove flywheel housing.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: The engine must be put in time before the flywheel housing is removed. This is done to make sure that the rear gear group is in alignment with the rotation of the engine, as shown.
- Remove bolts (3), plate (2), and idler gear (1).
Show/hide table
Illustration 1 | g06057006 |
- Use Tooling (A) and a suitable press to remove bearing (4).
Show/hide table
Illustration 3 g06057136 - Remove bolts (6), bolts (7), and idler gears (5).
Show/hide table
Illustration 4 g06057154 - Remove washers (8) and idler shaft (9).
Show/hide table
Illustration 5 g06057165 - Remove bolts (10) and cluster gear shaft (11).
Show/hide table
Illustration 6 g06057184 - Remove bolts (13) and crank gear (12).
Show/hide table
Illustration 2 | g06057041 |
- Install the gear group (rear) in the reverse order of removal.
- Tighten bolts (10) to a torque of
140 ± 10 N·m (103 ± 7 lb ft) . - Tighten bolts (7) and bolts (6) to a torque of
240 ± 20 N·m (177 ± 15 lb ft) .
- Tighten bolts (10) to a torque of
Caterpillar Information System:
XQP500 Generator Sets Setup
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734} NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
3512E Engines Engine Oil Sequence Valves - Remove and Install
XQP500 Generator Sets Refill Capacities
C9.3 Marine Auxiliary Engines Sensors and Electrical Components
XQP500 Generator Sets Product Lifting
Inspection of the 287-8585 Bushing and Pulley Assembly on Certain 3516C Generator Set Engines {1359} Inspection of the 287-8585 Bushing and Pulley Assembly on Certain 3516C Generator Set Engines {1359}
The 243-2501 Fan Guard May Crack on Certain 3500 Generator Set Engines {1353, 1360} The 243-2501 Fan Guard May Crack on Certain 3500 Generator Set Engines {1353, 1360}
An Improved Exhaust Manifold Group Is Now Used For Certain 3512E Engines {1059} An Improved Exhaust Manifold Group Is Now Used For Certain 3512E Engines {1059}
C9.3 Marine Auxiliary Engines Safety Messages
XQP500 Generator Sets Electrical System
C7.1 Marine Engine Fuel Priming Pump - Remove and Install
XQP500 Generator Sets Product Description
C7.1 Marine Engine Fuel Filter Base - Remove and Install
3512E Engines Piston Cooling Jets - Remove and Install
Inadvertent Advanced Control Joystick (ACJ) Float Control Activation Occurs On Certain Motor Graders {3168, 4343, 5063, 5705, 7000} Inadvertent Advanced Control Joystick (ACJ) Float Control Activation Occurs On Certain Motor Graders {3168, 4343, 5063, 5705, 7000}
C7.1 Marine Engine Fuel Cooler - Remove and Install
XQP500 Generator Sets Safety Messages
3512E Engines Cylinder Liner - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Is Restricted
The Compressor By-Pass Valve Actuator Might Fail On Certain G3500B Engines {1803, 5510, 7602, 7610, 7620} The Compressor By-Pass Valve Actuator Might Fail On Certain G3500B Engines {1803, 5510, 7602, 7610, 7620}
UPS 750 Uninterruptible Power Supply Battery Booster Interface
UPS 750 Uninterruptible Power Supply Inter-System Network Board
3512E Petroleum Engine Turbocharger