Engine Oil Filter Housing - Remove and Install
Start By:
- Remove fuel filter housing.
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1).
Show/hide table
Illustration 2 g03845636 - Remove bolts (2).
Show/hide table
Illustration 3 g03845661 - Remove bolts (5), guard assembly (4), and guard assembly (6).
Show/hide table
Illustration 4 g03845922 - Remove bolts (7) and guard assembly (8).
Show/hide table
Illustration 5 g03845959 - Remove bolts (9) and plate (10).
Show/hide table
Illustration 6 g03845982 - Disconnect harness assemblies (11). Remove pressure sensor (12) and pressure sensor (13).
Show/hide table
Illustration 7 g03846145 - Remove bolts (14) and plates (15).
Show/hide table
Illustration 8 g03846279 - Disconnect coupling assembly (17), coupling assembly (19), tube assembly (16), and tube assembly (18).
Show/hide table
Illustration 9 g03846303 - Remove bolt (21) and clamps (22). Disconnect tube assembly (20).
Show/hide table
Illustration 10 g03846476 - Remove bolts (23) and regulator housing (24).
Show/hide table
Illustration 11 g03846487 - Use a suitable lifting device to remove engine oil filter housing (25). The weight of engine oil filter housing (25) is approximately
55 kg (121 lb) . - Remove bolts (26) and engine oil filter housing (25).
Show/hide table
| |
| Illustration 1 | g03845624 |
- Install engine oil filter housing (25) in the reverse order of removal.
- Tighten bolts (14) to a torque of
135 ± 20 N·m (100 ± 15 lb ft) . - Tighten pressure sensor (13) and pressure sensor (12) to a torque of
10 ± 2 N·m (86 ± 180 lb in) .
- Tighten bolts (14) to a torque of
Caterpillar Information System:
3412 Generator Set Shutdown - Test
Cat® MineStar System A5:N2 Router Setup and Configuration Guide {7008, 7605} Cat® MineStar System A5:N2 Router Setup and Configuration Guide {7008, 7605}
C32 Marine Engines Aftercooler - Install
C32 Marine Engines Aftercooler - Remove
G3606 and G3608 Engines Prelubrication Oil Pump - Install
G3600 A4 Engines Manual Stop Procedure
G3600 A4 Engines Before Starting Engine
G3600 A4 Engines Product Lifting
3512C Generator Set Engine Engine Oil Pump - Remove and Install
G3600 A4 Engines Engine Stopping
3512C Generator Set Engine Engine Oil Cooler - Assemble
3512C Generator Set Engine Engine Oil Cooler - Disassemble
794 AC Off-Highway Truck Field Assembly Air Lines (Turbocharger) - Install
3412 Generator Set Speed Control (Engine Speed Switch) - Test
Energy Storage System General Information
3412 Generator Set Speed Control (PWM) - Test
Energy Storage System Abbreviations and Acronyms
Energy Storage System Site Considerations
Energy Storage System Service Tools
Energy Storage System Site Inspection and Material Inventory
Energy Storage System Equipment
Energy Storage System Enclosure Placement and Anchoring
Energy Storage System Mechanical Assembly
Energy Storage System Cathode Fan Wiring