Fuel Filter Housings - Assemble
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Put O-ring seal (15) and cover (14) in position on housing (6) and install the bolts that hold the cover in place.
- Put valve (17) in position in housing (6).
- Install O-ring seal (9) on plug (8). Put clean engine oil on the plug.
- The groove of valve (17) must be aligned with the opening for plug (8). Install plug (8) in housing (6).
- Install O-ring seal (12) on plug (13). Put clean engine oil on the O-ring seal.
- Install ball (10), spring (11), and plug (13) in housing (6).
- Install O-ring seals (16) and (18). Put housing (6) in position on the end of the fuel filter housing and install the bolts that hold the housing in place.
Show/hide table
Illustration 3 g00618078 - Put shaft assembly (7) in position on the valve and install bolt (5).
- Install check valves (4). The arrows must be pointing away from housing (6).
- Install tube assembly (3).
- If the engine is equipped with check valves, install check valves (2) and tube assembly (1). The arrows on the housing must be pointing away from housing (6).
Show/hide table
| |
| Illustration 1 | g00618080 |
Show/hide table
| |
| Illustration 2 | g00618083 |
Show/hide table
 |
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
End By:
- Install the fuel filter housings. Refer to Disassembly and Assembly, "Fuel Filter Housings - Install".
Caterpillar Information System:
C280-16 Engine Fuel Filter Housings - Disassemble
C3.3B Engines for Caterpillar Built Machines Camshaft Position Sensor Bushing - Remove and Install
C1.5 and C2.2 Engines for Caterpillar Built Machines Belt Tension Chart
C1.5 and C2.2 Engines for Caterpillar Built Machines Piston and Rings
C13, C15, and C18 Tier 4 Final Engines Exhaust Cooler (NRS)
C9.3 Tier 4 Final Engines Inlet Manifold Air Pressure Sensor
C6.6 Generator Sets Refill Capacities
CX31 On-Highway Transmission Torque Converter Housing
C3.4B Industrial Engine Plate Locations and Film Locations - Aftertreatment
C32 Generator Set Overhaul Considerations
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Design
C280-16 Engine Fuel Filter Housings - Remove
C280-16 Engine Fuel Filter Housings - Install
C13, C15, and C18 Tier 4 Final Engines Nitrogen Oxide Sensor - Engine Exhaust Out
C13, C15, and C18 Tier 4 Final Engines Nitrogen Oxide Sensor - Exhaust Pipe Out
3512E Land Electric Drive Coolant (ELC) - Change
3512E Land Electric Drive Coolant (DEAC) - Change
C7.1 Marine Generator Set Control Panel - EMCP 4.2 (If Equipped)
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Electronic Service Tool Does Not Communicate
3516C HD Petroleum Well Service Engines Electronic Control Module (ECM)
C13, C15, and C18 Tier 4 Final Engines Relay (ARD Nozzle Heater)
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines
C13, C15, and C18 Tier 4 Final Engines Mounting Frame
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines