Camshaft Position Sensor Bushing - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 435-3013 | 衬套工具 | 1 |
开始:
- 拆卸凸轮轴位置传感器。
- 拆下凸轮轴。
- 使用工具 (A) 拆下衬套 (1)。
Show/hide table
图 1 | g03376024 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 435-3013 | 衬套工具 | 1 |
B | - | Loctite 962T | - |
- 将工具 (B) 涂抹到衬套 (1) 的外径上。
注: 从齿轮系侧将衬套 (1) 安装至尺寸 (X)。 尺寸 (X) 为
0.10 to 0.60 mm (0.004 to 0.024 inch) 。 可以在曲轴箱的传感器侧测量尺寸 (X)。 衬套 (1) 的正确安装为进入曲轴箱 (2) 内尺寸 (X) 的深度。 - 使用工具 (A) 将衬套 (1) 安装到曲轴箱 (2) 上。
Show/hide table
图 2 | g03375894 |
飞轮侧 |
Show/hide table
图 3 | g03377023 |
曲轴箱的传感器侧 |
结束:
- 安装凸轮轴。
- 安装凸轮轴位置传感器。
Caterpillar Information System:
C1.5 and C2.2 Engines for Caterpillar Built Machines Belt Tension Chart
C1.5 and C2.2 Engines for Caterpillar Built Machines Piston and Rings
C13, C15, and C18 Tier 4 Final Engines Exhaust Cooler (NRS)
C9.3 Tier 4 Final Engines Inlet Manifold Air Pressure Sensor
C6.6 Generator Sets Refill Capacities
CX31 On-Highway Transmission Torque Converter Housing
C3.4B Industrial Engine Plate Locations and Film Locations - Aftertreatment
C32 Generator Set Overhaul Considerations
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Design
C280-16 Engine Fuel Filter Housings - Remove
374F Excavator Hydraulic System General Information (Swing System)
G3500H Generator Set Engine Sensor Supply - Test
C280-16 Engine Fuel Filter Housings - Disassemble
C280-16 Engine Fuel Filter Housings - Assemble
C280-16 Engine Fuel Filter Housings - Install
C13, C15, and C18 Tier 4 Final Engines Nitrogen Oxide Sensor - Engine Exhaust Out
C13, C15, and C18 Tier 4 Final Engines Nitrogen Oxide Sensor - Exhaust Pipe Out
3512E Land Electric Drive Coolant (ELC) - Change
3512E Land Electric Drive Coolant (DEAC) - Change
C7.1 Marine Generator Set Control Panel - EMCP 4.2 (If Equipped)
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Electronic Service Tool Does Not Communicate
3516C HD Petroleum Well Service Engines Electronic Control Module (ECM)
C13, C15, and C18 Tier 4 Final Engines Relay (ARD Nozzle Heater)
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines