Auxiliary Water Pump
Show/hide table
Illustration 1 | g03828292 |
Show/hide table
Specification for 312-7707 Auxiliary Water Pump Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
1 | 4 | 249-6365 Taperlock Stud | Torque to |
2 | 1 | 271-4926 Seal | Lubricate the bore lightly with glycerin or approved equivalent. |
3 | 3 | 2Y-5829 Nut | Torque to |
4 | 3 | 8T-7044 Taperlock Stud | Torque to |
5 | 1 | 212-8180 Pump Drive Shaft As | The end of the pump shaft must be flush with the face of the impeller within |
Before pressing the impeller on the shaft, lubricate the shaft with clean engine oil. | |||
Diameter of the shaft is |
|||
Width in the groove of the shaft for the thrust washer is |
|||
6 | 1 | 7N-4758 Thrust Washer | Thickness is |
7 | 1 | 271-4928 Seal | Lubricate the bore lightly with glycerin or approved equivalent. |
8 | 1 | 416-0603 Seal Gp | Use the following procedure to install the seal group.
1. Lubricate the outside diameter of the ceramic ring (11) and rubber seal (10) with clean water or with 207-1600 Rubber Lubricant. 2. Seat the ceramic ring (11) and the rubber seal (10) into the housing. 3. Remove the spring (13) from the seal assembly (12). 4. Press the seal assembly on the shaft until the faces of the seal makes the contact lightly. 5. Install the spring. |
9 | 1 | 8C-5236 Lip Type Seal | Do not lubricate the sealing lip. |
B | - | - | Bore of the impeller is |
C | - | - | Distance between the vanes of the impeller and the outside of the housing is |
Caterpillar Information System:
C280 Marine Engines Lubrication System Operation
G3500 Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Electronic Control (Diesel Exhaust Fluid)
G3500 A3 Engines Exhaust Manifold - Water Cooled
C175-16 Locomotive Engine Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
G3500 A3 Engines Exhaust Manifold
G3500 A3 Engines Turbocharger
G3500 Engines Exhaust Manifold - Water Cooled
G3516 Engines Gas Shutoff Valve
Inspecting the Diesel Oxidation Catalyst (DOC) and the Diesel Particulate Filter (DPF) After the NRS Cooler Fails{108F, 108G} Inspecting the Diesel Oxidation Catalyst (DOC) and the Diesel Particulate Filter (DPF) After the NRS Cooler Fails{108F, 108G}
G3500 Engines Turbocharger
G3516 Engines Stub Shaft (Front)
G3500 Engines Piston and Rings
C280-16 Generator Set Engine for Nuclear Applications Camshaft Timing
C280-16 Generator Set Engine for Nuclear Applications Engine Speed/Timing Sensor
G3512H and G3516H Generator Set Engines Rocker Shaft and Push Rod - Remove and Install
C280-16 Generator Set Engine for Nuclear Applications Speed Control
G3512H and G3516H Generator Set Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
G3512H and G3516H Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
G3512H and G3516H Generator Set Engines Flywheel Housing - Remove and Install
G3512H and G3516H Generator Set Engines Gear Group (Rear) - Remove and Install
C280 Marine Engines Engine Governing - Adjust
G3512H and G3516H Generator Set Engines Crankshaft Main Bearings - Remove and Install
C4.4 and C7.1 Engines Injector Solenoid - Test