Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
Show/hide table
图 1 | g03418193 |
Show/hide table
技术规格,适用于 380-4432 压力控制阀总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 360-2963 O 形密封圈 | 装配前,使用所密封的油液稍稍润滑孔。 |
2 | 1 | 285-6589 弹簧 | 机油旁通阀使用的弹簧:
测试力下的长度为 测试力为 测试后的自由长度为 |
3 | 1 | 288-4597 弹簧 | 机油调节器阀使用的弹簧:
测试力下的长度为 测试力为 测试后的自由长度为 |
Show/hide table
图 2 | g03410187 |
Show/hide table
图 3 | g03410202 |
Show/hide table
测试规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
A | - | - | 压力口 |
B | - | - | 油箱端口 |
C | - | - | 油道端口 |
D | - | - | 阀芯单向阀 |
E | - | 177-7131 垫片 (1)
或 177-7130 垫片 (2) |
调节器阀和垫片 |
F | - | 177-7131 垫片 (1)
或 177-7130 垫片 (2) |
旁通阀和垫片 |
测试要求 | |||
- | - | - | 1. 将测试台架安全压力设定为 |
2. 对于所有测试,保留油道端口上的盖 | |||
测试步骤 | |||
- | - | - | 使用以下测试步骤测试压力控制阀: |
1. 泄漏检查 A. 向压力口施加 B. 来自油箱端口的最大允许流量是 |
|||
2. 旁通阀测试 A. 排气"总成"端口至大气 B. 向压力口施加 注:阀的开启压力应为 1. 一个 177-7130 垫片可使压力升高大约 2. 一个 177-7131 垫片可使压力升高大约 |
|||
3. 调节器阀测试 A. 将"总成"端口连接至压力口 B. 向压力口施加 C. 在油箱端口应能看到完整流量 注:开启压力应为 1. 一个 177-7130 垫片可使压力升高大约 2. 一个 177-7131 垫片可使压力升高大约 |
Show/hide table
(1) | |
(2) | |
Caterpillar Information System:
G3500 A3 Engines Exhaust Manifold
G3500 A3 Engines Turbocharger
G3500 Engines Exhaust Manifold - Water Cooled
G3516 Engines Gas Shutoff Valve
Inspecting the Diesel Oxidation Catalyst (DOC) and the Diesel Particulate Filter (DPF) After the NRS Cooler Fails{108F, 108G} Inspecting the Diesel Oxidation Catalyst (DOC) and the Diesel Particulate Filter (DPF) After the NRS Cooler Fails{108F, 108G}
G3500 Engines Turbocharger
G3516 Engines Stub Shaft (Front)
G3500 A3 Engines Vibration Damper Guard
G3516 Engines Vibration Damper Guard
G3516 Engines Engine Oil Pan
G3500J Petroleum Engines Jacket Water Heater Mount
G3500J Petroleum Engines Jacket Water Heater Mount
G3500 A3 Engines Exhaust Manifold - Water Cooled
C13, C15, and C18 Tier 4 Final Engines Electronic Control (Diesel Exhaust Fluid)
G3500 Engines Turbocharger
C280 Marine Engines Lubrication System Operation
C175-16 Engine for 795F Series AC Off-Highway Trucks Auxiliary Water Pump
G3500 Engines Piston and Rings
C280-16 Generator Set Engine for Nuclear Applications Camshaft Timing
C280-16 Generator Set Engine for Nuclear Applications Engine Speed/Timing Sensor
G3512H and G3516H Generator Set Engines Rocker Shaft and Push Rod - Remove and Install
C280-16 Generator Set Engine for Nuclear Applications Speed Control
G3512H and G3516H Generator Set Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
G3512H and G3516H Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install