Water Control Valve - Adjust
Show/hide table
| Required Parts | |||
|---|---|---|---|
| Tool | Qty | Part Number | Part Description |
| 1 | 7 | 431-9716 | Water Control Valve Gp |
- Locate valve group (1). Loosen bolts (B) on one split flange (A). Remove the other split flange (not shown).
Note: Make sure that valve group O-ring seal is in place.
Show/hide table
Illustration 2 g03350191 Show/hide table
Illustration 3 g03350201 - Install valve group (1) on spray bar (C). Reinstall split flanges (A). Do not tighten the mounting bolts.
Show/hide table
Illustration 4 g03350204 Show/hide table
Illustration 5 g03350212 - Rotate valve group (1) on spray bar (C) in order to obtain the desired direction for water spray. Tighten the mounting bolts on both flanges to a torque of
55 ± 10 N·m (40.56580 ± 7.37560 lb ft) .Note: Orient the spray heads as shown with each spray head angled 20 degrees away from the center line.
Show/hide table
Illustration 6 g03350213 - Repeat the previous steps for the remaining spray heads on the rear spray bar.
Show/hide table
Illustration 7 g03350218 - Install valve group (1) on front spray bar (D). Reinstall split flanges (A). Do not tighten the mounting bolts.
Note: Two spray heads can be installed on the front of the truck. The spray head on the left side of the truck is shown above.
- Rotate valve group (1) on spray bar (D) in order to obtain the desired direction for water spray. Tighten the mounting bolts.
- Repeat the previous steps for the remaining spray head on the opposite side of the water tank.
Show/hide table
| |
| Illustration 1 | g03350189 |
Caterpillar Information System:
349F and 352F Excavators Machine System Specifications Boom Cylinder
C4.4 (Mech) Marine Generator Set MCS-3 Maintenance Interval Schedule - Naturally Aspirated Marine Generator Sets
3516B Engine for the MT4400D Off-Highway Truck Flywheel Housing
3512E Tier 4 Final Engines for Land Electric Drilling Flywheel
G3500H 50Hz Generator Sets Fluid Recommendations
G3500 Generator Sets Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
Recommendations for Rebuilding Torque Converter Freewheel Stators on All Cat Products {3101, 3129} Recommendations for Rebuilding Torque Converter Freewheel Stators on All Cat Products {3101, 3129}
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Pressure Sensor (Water Level) - Calibrate
374F Excavator Hydraulic System Electronic Control (Stick System)
G3500H 50Hz Generator Sets Alarms and Shutoffs
966M Tier 4 and 972M Tier 4 Wheel Loaders Power Train Torque Converter (Freewheel Stator) (Lockup) - Assemble
G3500H 50Hz Generator Sets Plate Locations and Film Locations
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Water Control Valve - Calibrate
349F and 352F Excavators Machine System Specifications Hydraulic Oil Cooler Lines Group
2013/03/29 Improved VisionLinkTMStore is Now Available for all Caterpillar Products {7606}
2013/03/13 A New Injector Hydraulic Pump Group Is Available For Certain C9 Marine Engines {1714}
2013/03/29 Device Transfers Are Now Supported In VisionLinkTM Store {7606}
2013/03/29 Improved VisionLinkTM Store for Minimizing Delay in Appearance of VisionLink Store - Modules is Now Available for All Caterpillar Products {7606}
G3500H 50Hz Generator Sets Additional Messages
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Boost Pressure Sensor
C7.1 Marine Engine Air Starting Motor - Remove and Install
C18 Marine Engines Diagnostic Trouble Codes
C7.1 Marine Engine Fuel Injection Lines - Remove and Install - Non M.C.S. Fuel Injection Lines
C7.1 Marine Engine Fuel Injection Lines - Remove and Install - Double Wall Fuel Injection Lines