Flywheel Housing
Show/hide table
 | |
| Illustration 1 | g03356025 |
Show/hide table
 | |
| Illustration 2 | g03356026 |
Front view of engine | |
Show/hide table
| Specification for 390-3456 Flywheel Housing Gp | |||
| Item | Qty | Part | Specification Description |
| Before installation of the flywheel housing, inspect the front face of the flywheel housing and the rear face of the cylinder block. The components must be free of the following substances: oil, fuel, water, gasket adhesive, assembly compounds, and any other foreign materials. | |||
| To seal the joint between the flywheel housing and the cylinder block, apply red Loctite 596 to the front face of the flywheel housing. | |||
| 1 | 4 | 9X-8875 Bolt | Length of 1/2 inch diameter bolt is 88.90 mm (3.500 inch). Torque to 135 ± 20 N·m (100 ± 15 lb ft). |
| 2 | 6 | 9X-8873 Bolt | Length of 1/2 inch diameter bolt is 57.15 mm (2.250 inch). Torque to 135 ± 20 N·m (100 ± 15 lb ft). |
| 3 | 2 | 9M-7269 Bolt | Length of 1/2 inch diameter bolt is 171.5 mm (6.75 inch). Torque to 135 ± 20 N·m (100 ± 15 lb ft). |
| 4 | 2 | 9S-1374 Bolt | Length of 1/2 inch diameter bolt is 203.20 mm (8.000 inch). Torque to 135 ± 20 N·m (100 ± 15 lb ft). |
| 5 | 4 | 8S-9089 Bolt | Length of 1/2 inch diameter bolt is 114.30 mm (4.500 inch). Torque to 135 ± 20 N·m (100 ± 15 lb ft). |
| 6 | 16 | 1D-4590 Bolt | Length of 5/8 inch diameter bolt is 120.65 mm (4.750 inch). Torque to 270 ± 40 N·m (199 ± 30 lb ft). |
| 7 | - | - | After assembly, trim gasket flush to face (8). |
Caterpillar Information System:
3512E Tier 4 Final Engines for Land Electric Drilling Flywheel
G3500H 50Hz Generator Sets Fluid Recommendations
G3500 Generator Sets Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
Recommendations for Rebuilding Torque Converter Freewheel Stators on All Cat Products {3101, 3129} Recommendations for Rebuilding Torque Converter Freewheel Stators on All Cat Products {3101, 3129}
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Pressure Sensor (Water Level) - Calibrate
374F Excavator Hydraulic System Electronic Control (Stick System)
G3500H 50Hz Generator Sets Alarms and Shutoffs
966M Tier 4 and 972M Tier 4 Wheel Loaders Power Train Torque Converter (Freewheel Stator) (Lockup) - Assemble
G3500H 50Hz Generator Sets Plate Locations and Film Locations
C4.4 (Mech) Marine Generator Set MCS-3 Maintenance Interval Schedule - Turbocharged Aftercooled Marine Generator Sets Rated at 50 Hz 86 ekW and 60 Hz 93 ekW
2013/04/04 A New Thermostat Housing Bracket Is Used for Certain 3516C Marine Engines {1355}
XQP150 Rental Generator Set Engine Crankcase Breather Element - Replace
C4.4 (Mech) Marine Generator Set MCS-3 Maintenance Interval Schedule - Naturally Aspirated Marine Generator Sets
349F and 352F Excavators Machine System Specifications Boom Cylinder
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Water Control Valve - Adjust
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Water Control Valve - Calibrate
349F and 352F Excavators Machine System Specifications Hydraulic Oil Cooler Lines Group
2013/03/29 Improved VisionLinkTMStore is Now Available for all Caterpillar Products {7606}
2013/03/13 A New Injector Hydraulic Pump Group Is Available For Certain C9 Marine Engines {1714}
2013/03/29 Device Transfers Are Now Supported In VisionLinkTM Store {7606}
2013/03/29 Improved VisionLinkTM Store for Minimizing Delay in Appearance of VisionLink Store - Modules is Now Available for All Caterpillar Products {7606}
G3500H 50Hz Generator Sets Additional Messages
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Boost Pressure Sensor
C7.1 Marine Engine Air Starting Motor - Remove and Install