Cylinder Head Valves
Show/hide table
Illustration 1 | g03345806 |
Show/hide table
Specification for 380-9100 Cylinder Head Gp     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 24     | 247-9908 Spring     | Length under test force is 67.12 mm (2.643 inch). Test force is 320 ± 25 N (72 ± 6 lb). Free length after test is 76.70 mm (3.020 inch).     |
2     | 24     | 211-3122 Spring     | Length under test force is 60.14 mm (2.370 inch). Test force is 150 ± 12 N (34 ± 3 lb). Free length after test is 71.70 mm (2.823 inch).     |
3     | 12     | 153-7024 Exhaust Valve     | Before assembly, coat the exhaust valve stems with clean engine oil. Stem diameter (A) is 9.441 ± 0.010 mm (0.37169 ± 0.00039 inch). Valve head diameter (C) is 41.81 ± 0.13 mm (1.646 ± 0.005 inch). Face angle is 45.75 ± 0.25 degrees.     |
4     | 12     | 153-7023 Inlet Valve     | Before assembly, coat the inlet valve stems with clean engine oil. Stem diameter (B) is 9.441 ± 0.010 mm (0.37169 ± 0.00039 inch). Valve head diameter (D) is 47.00 ± 0.13 mm (1.850 ± 0.005 inch). Face angle is 60.75 ± 0.25 degrees.     |
5     | 24     | 376-6566 Valve Guide     | Bore of the inlet and exhaust valve guide after installation is 9.502 ± 0.013 mm (0.3740 ± 0.0005 inch).     |
6     | 12     | 224-3983 Seat Insert     | Outside diameter of inlet valve seat insert is 48.025 ± 0.013 mm (1.8907 ± 0.0005 inch). Bore in the cylinder head is 47.950 ± 0.025 mm (1.8878 ± 0.0009 inch). Face angle is 30.25 ± 0.25 degrees.     |
7     | 12     | 226-5561 Valve Seat Insert     | Outside diameter of exhaust valve seat insert is 42.840 ± 0.013 mm (1.6866 ± 0.0005 inch). Bore in the cylinder head is 42.774 ± 0.025 mm (1.6840 ± 0.0010 inch). Face angle is 45.25 ± 0.25 degrees.     |
Caterpillar Information System:
C32 Marine Engines Electric Starting Motor
C18 Marine Propulsion Engines Camshaft
C7.1 Industrial Engine Diagnostic Flash Code Retrieval
C18 Marine Propulsion Engines Piston and Rings
C32 Marine Engines Exhaust Manifold - Water cooled
C7.1 Marine Engine Exhaust Manifold - Remove and Install
C7.1 Marine Engine Inlet Manifold - Remove and Install
C175-16 Locomotive Engine Coolant Temperature Is High
C280-16 Engine Safety Messages
2013/02/11 Updating the Fuel Filter Group on Certain C27 and C32 Industrial Engines {1261, 1262}
NOx Sensors Handling and Installation Procedures {191N} NOx Sensors Handling and Installation Procedures {191N}
C280-16 Engine Model View Illustrations
C9.3 Head Tool Improvements{0599, 0701, 0703, 1100} C9.3 Head Tool Improvements{0599, 0701, 0703, 1100}
C7.1 Engines for Caterpillar Built Machines Piston and Rings
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
2013/02/08 A New Turbocharger Group Is Available for Certain C15 Truck Engines {1052, 1053}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Fuel Pressure Problem - Gas System
2013/02/22 Bearing Upgrade from Pre 2.4 or 2.4 Bearings to 3.5 Bearing on Certain Uninterruptible Power Supply {4480, 7551}
C18 Marine and Marine Generator Set Engines Auxiliary Water Pump - Sea Water
C7.1 Engines for Caterpillar Built Machines Speed/Timing Sensor
C18 Marine Propulsion Engines Auxiliary Water Pump - Sea Water
C7.1 Engines for Caterpillar Built Machines Engine Oil Pump
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (Rail)
C7.1 Engines for Caterpillar Built Machines Crankshaft Seals