Electric Starting Motor
Show/hide table
 | |
| 图 1 | g03345790 |
Show/hide table
| 355-8842 电起动马达总成 技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | - | - | 拧紧至扭矩为 8.75 ± 1.05 N·m (77.44 ± 9.29 lb in)。 |
| 2 | 1 | 045-4065 螺钉 | 拧紧至扭矩为 2.6 ± 0.8 N·m (23.0 ± 7.1 lb in)。 |
| 3 | 1 | 045-4065 螺钉 | 开关端子必须用热收缩管绝缘。 不要使用模压端子。 拧紧至扭矩为 2.6 ± 0.8 N·m (23.0 ± 7.1 lb in)。 |
| 4 | 1 | 6V-8188 螺母 | 接地终端。 最终安装扭矩为 30.5 ± 3.5 N·m (269.9 ± 30.9 lb in)。 |
| 5 | 1 | 6V-8188 螺母 | 马达机架终端。 最终安装扭矩为 30.5 ± 3.5 N·m (269.9 ± 30.9 lb in)。 |
| 6 | 1 | - | 起动继电器端子（高侧）。 最终安装扭矩为 2.25 ± 0.25 N·m (19.91 ± 2.21 lb in)。 |
| 7 | 1 | - | 起动继电器端子接地（低侧）。 最终安装扭矩为 2.25 ± 0.25 N·m (19.91 ± 2.21 lb in)。 |
| 8 | 1 | 6V-8188 螺母 | 马达终端。 最终安装扭矩为 30.5 ± 3.5 N·m (269.9 ± 30.9 lb in)。 |
| 9 | 1 | 6V-8188 螺母 | 蓄电池终端。 蓄电池端子螺母之间最多可使用三个电缆端子或导线端子。 两个电缆接线端可以等于或高于 0 AWG。 最终安装扭矩为 30.5 ± 3.5 N·m (269.9 ± 30.9 lb in)。 |
| B | - | - | 小齿轮和壳体之间的间隙为 9.1 mm (0.36 in)。 |
| - | - | - | 工作温度范围为 −25° 至 121 °C (−45° 至 217 °F)。 |
| - | - | - | 工作电压为 24 VDC。 |
| - | - | - | 20 V 和 25° C (77° F) 时的吸合电流为 49.3 ± 3.3 安培。 |
| - | - | - | 20 V 和 25° C (77° F) 时的保持电流最大为 6.8 安培。 |
| - | - | - | 当从小齿轮端观看电起动马达时，马达顺时针旋转。 |
| - | - | - | 25 °C (77 °F) 时的无负载性能： |
| 转速为 6612 ± 1887.5 rpm。 | |||
| 电流消耗为 100 ± 30 安培。 | |||
| 电压为 23 VDC。 | |||
Caterpillar Information System:
C18 Marine Propulsion Engines Camshaft
C7.1 Industrial Engine Diagnostic Flash Code Retrieval
C18 Marine Propulsion Engines Piston and Rings
C32 Marine Engines Exhaust Manifold - Water cooled
C7.1 Marine Engine Exhaust Manifold - Remove and Install
C7.1 Marine Engine Inlet Manifold - Remove and Install
C175-16 Locomotive Engine Coolant Temperature Is High
C280-16 Engine Safety Messages
2013/02/11 Updating the Fuel Filter Group on Certain C27 and C32 Industrial Engines {1261, 1262}
NOx Sensors Handling and Installation Procedures {191N} NOx Sensors Handling and Installation Procedures {191N}
C280-16 Engine Model View Illustrations
C27 Generator Set Safety Messages
C18 Marine Propulsion Engines Cylinder Head Valves
C9.3 Head Tool Improvements{0599, 0701, 0703, 1100} C9.3 Head Tool Improvements{0599, 0701, 0703, 1100}
C7.1 Engines for Caterpillar Built Machines Piston and Rings
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
2013/02/08 A New Turbocharger Group Is Available for Certain C15 Truck Engines {1052, 1053}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Fuel Pressure Problem - Gas System
2013/02/22 Bearing Upgrade from Pre 2.4 or 2.4 Bearings to 3.5 Bearing on Certain Uninterruptible Power Supply {4480, 7551}
C18 Marine and Marine Generator Set Engines Auxiliary Water Pump - Sea Water
C7.1 Engines for Caterpillar Built Machines Speed/Timing Sensor
C18 Marine Propulsion Engines Auxiliary Water Pump - Sea Water
C7.1 Engines for Caterpillar Built Machines Engine Oil Pump
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (Rail)