Bearing Clearance - Check
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 198-9142 | 塑料量规(绿色) 0.025 至 0.076 mm (0.001 至 0.003 in) |
1 |
198-9143 | 塑料量规(红色) 0.051 至 0.152 mm (0.002 至 0.006 in) |
1 | |
198-9144 | 塑料量规(蓝色) 0.102 至 0.229 mm (0.004 至 0.009 in) |
1 | |
198-9145 | 塑料量规(黄色) 0.230 至 0.510 mm (0.009 至 0.020 in) |
1 |
注: 当发动机安装在底盘上时,可能不需要塑料量规。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: Caterpillar 不推荐检查实际的轴承间隙,尤其是在小型发动机上。 这是因为可能会出现结果不准确,轴承或轴径可能被损坏。 每个 Caterpillar 发动机轴承都要进行特殊的壁厚质量检查。
注: 测量值应在技术规格内且必须使用正确的轴承。 如果在解体期间测量了缸体和连杆的曲轴轴颈和孔,则不需要做进一步检查。 然而,如果技师仍然想要测量轴承间隙,使用工具 (A) 也是可以测量的。 如果间隙小于
Show/hide table
注意 |
---|
导线、塞尺或量缸表可能会损坏轴承面。 |
技师必须非常仔细正确地使用工具 (A)。 必须记住以下要点:
- 确保轴承和孔的后面清洁和干燥。
- 确保轴承锁片正确就位于锁片槽内。
- 曲轴与工具 (A) 的触点上不能沾有油。
- 将工具 (A) 置于盖中的轴承顶部。
注: 不允许工具 (A) 延伸到轴承边缘外。
- 使用正确的转动扭矩技术规格安装轴承盖。 不要使用冲击扳手。 在安装盖时小心不要撞出轴承。
注: 安装工具 (A) 时不要转动曲轴。
- 小心地拆卸盖,但不要卸掉工具 (A) 。 工具 (A) 在轴承盖或曲轴轴颈上时测量工具 (A) 的宽度。 参考图 1。
Show/hide table
图 1 g01152855 典型示例 - 安装轴承盖前拆卸全部的工具 (A)。
注: 用工具 (A) 测得的读数有时不清晰。 例如,工具 (A) 的所有零件并不一样宽。 测量主要宽度确保零件符合技术规格。 有关正确的间隙,请参阅技术规格手册, "连杆轴承轴颈"和技术规格手册, "主轴承轴颈"。
Caterpillar Information System:
3508B, 3512B, and 3516B High Displacement Generator Sets Maintenance Interval Schedule - Standby
C175-16 PETROLEUM ENGINES Piston Cooling Jets - Remove and Install
New Engine Software Is Available for Certain Tier 4 Interim C9.3 Through C15 Machine Engines and C9.3 Through C18 Industrial Engines {1920} New Engine Software Is Available for Certain Tier 4 Interim C9.3 Through C15 Machine Engines and C9.3 Through C18 Industrial Engines {1920}
C175-16 PETROLEUM ENGINES Gear Group (Rear) - Remove and Install
2012/11/01 Inspection of RS485 Remote Annunciator Interface Harness On Certain 3500 Generator Sets {1408, 4490, 7400}
C175-16 PETROLEUM ENGINES Idler Gears (Front) - Remove and Install
3500 Engines Air Starting Motor
3500 Engines Air Starting Motor
C175-16 Engine Sensor Signal (Analog, Active) - Test
2013/10/31 New Exhaust Components Are Used on Certain 3500B and 3500C Engines {1059}
3500C Marine Engines Air Starting Motor
C175-16 PETROLEUM ENGINES Flywheel Housing - Remove and Install
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206} Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
2012/10/18 New Plugs Are Available for Reconditioning the Water Ferrules in 3500 Engine Blocks {1201}
C175-16 Generator Set Engine Connecting Rod Bearings - Remove and Install
C175-16 Generator Set Engine Crankshaft Main Bearings - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Aftercooler Core - Inspect/Clean/Test
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant (DEAC) - Change
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant (ELC) - Change
C3.3B and C3.8 Engines for Caterpillar Built Machines Starting Aid - Test
2012/12/11 A New Wastegate Bellows and Gaskets Are Used On Certain 3500C Marine Engines {1059}
3512C SR4B Generator Sets Engine Oil and Filter - Change
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant Extender (ELC) - Add
C175-16 PETROLEUM ENGINES Pistons, Liners, and Connecting Rods - Remove and Install