Idler Gears (Front) - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0520 | 冲头总成 | 1 |
开始:
- 拆卸发动机机油和水泵驱动器。 参考拆解与组装, "发动机机油和水泵驱动器 - 拆卸"。
- 拆卸燃油和辅助水泵驱动器。 参考拆解与组装, "燃油和辅助水泵驱动器 - 拆卸"。
- 拆卸减振器。 参考拆解和组装, "减振器 - 拆卸和安装"。
- 拆下螺栓 (1 )。 拆下罩盖 (2)。 拆下螺栓 (3 )。 拆下盖 (4)。 卸下螺栓 (5)。 拆下螺栓 (6)。
Show/hide table
图 2 g01229251 Show/hide table图 3 g01229252 - 支撑住惰轮 (7)。 拆下销 (8)。 从销 (8) 上拆下 O 形密封圈。 将惰轮 (7) 降到前驱动壳体底部。 从前驱动壳体背面拆卸惰轮 (7)。
Show/hide table
图 4 g01229253 - 使用工具 (A) 和适当的压具,将轴承 (9) 从齿轮 (7) 上拆下。
- 对于另一侧,重复步骤2 至3。
Show/hide table
图 1 | g01229249 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0520 | 冲头总成 | 1 |
- 使用工具 (A) 和适当的压具将轴承 (9) 安装到齿轮 (7) 中。
Show/hide table
图 6 g01229252 Show/hide table图 7 g01229251 - 将惰轮 (7) 安置在前驱动壳体背面。 将惰轮 (7) 从前驱动壳体底部提升到位。 将新的 O 形密封圈安装到销 (8) 上。 将销 (8) 装入惰轮 (7) 中。
- 对于另一侧,重复步骤1 至2。
Show/hide table
图 8 g01229249 - 安装螺栓 (6)。 安装螺栓 (5)。 安装盖 (4)。 安装螺栓 (3)。 安装罩盖 (2)。 安装螺栓 (1)。
Show/hide table
图 5 | g01229253 |
结束:
- 安装减振器。 参考拆解和组装, "减振器 - 拆卸和安装"。
- 安装燃油和辅助水泵驱动器。 参考拆解与组装, "燃油和辅助水泵驱动器 - 安装"。
- 安装发动机机油和水泵驱动器。 参考拆解与组装, "发动机机油和水泵驱动器 - 安装"。
Caterpillar Information System:
3500 Engines Air Starting Motor
3500 Engines Air Starting Motor
C175-16 Engine Sensor Signal (Analog, Active) - Test
2013/10/31 New Exhaust Components Are Used on Certain 3500B and 3500C Engines {1059}
3500C Marine Engines Air Starting Motor
C175-16 PETROLEUM ENGINES Flywheel Housing - Remove and Install
C3.3B and C3.8 Engines for Caterpillar Built Machines Exhaust Temperature Is High
C175-16 PETROLEUM ENGINES Crankshaft Rear Seal - Remove and Install
C175-16 PETROLEUM ENGINES Flywheel - Remove and Install
2012/11/26 A New Heat Shield and Related Components Are Used On Certain C9.3 Commercial Engines {1000}
C175-16 Generator Set Engine Crankshaft Front Seal - Remove and Install
C175-16 Generator Set Engine Vibration Damper - Remove and Install
2012/11/01 Inspection of RS485 Remote Annunciator Interface Harness On Certain 3500 Generator Sets {1408, 4490, 7400}
C175-16 PETROLEUM ENGINES Gear Group (Rear) - Remove and Install
New Engine Software Is Available for Certain Tier 4 Interim C9.3 Through C15 Machine Engines and C9.3 Through C18 Industrial Engines {1920} New Engine Software Is Available for Certain Tier 4 Interim C9.3 Through C15 Machine Engines and C9.3 Through C18 Industrial Engines {1920}
C175-16 PETROLEUM ENGINES Piston Cooling Jets - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Maintenance Interval Schedule - Standby
C175-16 PETROLEUM ENGINES Bearing Clearance - Check
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206} Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
2012/10/18 New Plugs Are Available for Reconditioning the Water Ferrules in 3500 Engine Blocks {1201}
C175-16 Generator Set Engine Connecting Rod Bearings - Remove and Install
C175-16 Generator Set Engine Crankshaft Main Bearings - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Aftercooler Core - Inspect/Clean/Test
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant (DEAC) - Change