Starting Aid - Test
Show/hide table
诊断代码 | |||
代码 | 说明 | 条件 | 备注 |
523544-3 | 空气加热器继电器驱动电路 + B 短路 | 当执行加热器继电器驱动指令时,蓄电池电压正常。 | 线束 + B 短路持续 1 秒或以上 警告级别 2 症状是起动故障和白烟增加。 |
523544-4 | 空气加热器继电器驱动电路对接地短路 | 当没有空气加热器继电器驱动指令时,蓄电池电压正常。 | 接地线束开路持续 1 秒或以上。 警告级别 2 症状是起动故障和白烟增加。 |
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
---|---|---|
1. 运行发动机,直到冷却液温度为 10 C (50 F) 或以上。 A. 检查 Cat® 电子技师 (ET) 中的“起动辅助继电器”。 B. 起动继电器系统的状态应为断开。 |
起动辅助继电器 |
结果:如果不正常,则检查导线线束和接头的导通性。 结果:如果正常,转至测试步骤 2。 |
2. 检查进气加热器继电器。 A. 断开冷却液温度接头。 B. 连接假负载电阻器(15 到 25 千欧)。 C. 这与 D. 检查 Cat ET,且起动辅助继电器应接通 |
进气加热器继电器 |
结果:如果不正常,则检查导线线束和接头的导通性。 结果:如果正常,转至测试步骤 3。 |
3. 测量进气继电器的信号和接地之间的电压。 |
电压 |
结果:·当继电器接通时,电压应等同于蓄电池电压。 结果:·当继电器断开时,电压应近似于 0 V。 |
4. 检查 + B 和主空气加热器继电器之间的导通性。 |
持续性 |
结果:当继电器接通时,应导通。 结果:当继电器断开时,应不导通。 |
Caterpillar Information System:
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant (ELC) - Change
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant (DEAC) - Change
3508B, 3512B, and 3516B High Displacement Generator Sets Aftercooler Core - Inspect/Clean/Test
C175-16 Generator Set Engine Crankshaft Main Bearings - Remove and Install
C175-16 Generator Set Engine Connecting Rod Bearings - Remove and Install
2012/10/18 New Plugs Are Available for Reconditioning the Water Ferrules in 3500 Engine Blocks {1201}
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206} Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
C175-16 PETROLEUM ENGINES Bearing Clearance - Check
3508B, 3512B, and 3516B High Displacement Generator Sets Maintenance Interval Schedule - Standby
C175-16 PETROLEUM ENGINES Piston Cooling Jets - Remove and Install
New Engine Software Is Available for Certain Tier 4 Interim C9.3 Through C15 Machine Engines and C9.3 Through C18 Industrial Engines {1920} New Engine Software Is Available for Certain Tier 4 Interim C9.3 Through C15 Machine Engines and C9.3 Through C18 Industrial Engines {1920}
C175-16 PETROLEUM ENGINES Gear Group (Rear) - Remove and Install
2012/12/11 A New Wastegate Bellows and Gaskets Are Used On Certain 3500C Marine Engines {1059}
3512C SR4B Generator Sets Engine Oil and Filter - Change
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant Extender (ELC) - Add
C175-16 PETROLEUM ENGINES Pistons, Liners, and Connecting Rods - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant Level - Check
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant Sample (Level 1) - Obtain
3508B, 3512B, and 3516B High Displacement Generator Sets Coolant Sample (Level 2) - Obtain
C175-16 PETROLEUM ENGINES Pistons and Connecting Rods - Disassemble
C175-16 PETROLEUM ENGINES Pistons and Connecting Rods - Assemble
2014/08/01 A New Fuel Transfer Pump Is Now Available for Certain C11 through C18 Industrial Engines {1256}
2014/08/07 A New Fuel Transfer Pump Is Now Available for Certain Truck Engines {1256}
C3.3B and C3.8 Engines for Caterpillar Built Machines Injector Data Incorrect - Test