Flow Limiter - Remove and Install
开始:
- 拆卸高压燃油油轨。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 6V-6195 | 联锁铰钳 | 1 |
B | 339-9352 | 喷油器 系统盖套件 | 1 |
265-2256 | 雨刷器 | 1 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
在燃油系统压力未得到释放之前,不要打开高压燃油系统。发动机关闭后,等待 10 分钟以释放燃油系统压力。工作中的燃油系统处于高压状态。暴露于高压燃油下可能导致人身伤害。 |
注: 用工具 (B) 盖住管组件、接头、端口以及燃油系统的所有开口,以防污染。
注: 不要拆下所有套管轴,以保持油轨对准。 一次拆卸一个,更换后再拆卸下一个。 如有必要,用新套管轴更换。
- 拆下螺栓 (3) 和垫圈。 拆下管组件 (1)。 断开线束组件 (2)。
Show/hide table
图 2 g02087089 - 将清洁的发动机机油涂在区域 (X)。 对另一侧套管轴重复此操作。 拆下螺栓 (4) 和螺栓 (6)。 拆卸管组件 (5)。
注: 用新螺栓 (4) 和 (6) 更换。
Show/hide table图 3 g02087090 - 使用工具 (A) 拆卸燃油油轨上的限流器 (7)。
注: 用保护盖盖住限流器 (7) 以防污染。 使用工具 (A) 前进行清洁,以防污染燃油系统。
Show/hide table
图 1 | g02087086 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 6V-6195 | 联锁铰钳 | 1 |
B | 339-9352 | 喷油器 系统盖套件 | 1 |
265-2256 | 雨刷器 | 1 |
注: 拆卸工具 (B) 时注意避免污染。
- 按与拆卸相反的顺序安装限流器 (7)。
- 安装新螺栓 (4) 和 (6) 并用手拧紧。 均匀地拧紧新螺栓 (4) 至扭矩为
20 N·m (15 lb ft) 。 均匀地拧紧新螺栓 (6) 至扭矩为20 N·m (15 lb ft) 。 均匀地拧紧新螺栓 (4) 至扭矩为40 N·m (30 lb ft) 。 均匀地拧紧新螺栓 (6) 至扭矩为40 N·m (30 lb ft) 。
- 安装新螺栓 (4) 和 (6) 并用手拧紧。 均匀地拧紧新螺栓 (4) 至扭矩为
Caterpillar Information System:
C32 Marine Engines Camshaft Bearings - Install
C175-16 Generator Set Engine High Pressure Fuel Rails - Remove and Install
C32 Marine Engines Camshaft Bearings - Remove
C1.5 and C2.2 Industrial Engines Exhaust Has Excessive White Smoke
C32 Marine Engines Unit Injector - Remove
C175-16 Generator Set Engine Fuel Transfer Pump - Remove and Install
C32 Marine Engines Unit Injector - Install
C175-16 Generator Set Engine Fuel Priming Pump - Remove and Install
2012/11/12 A New Seat Kit is Now Available for Certain Excavators and Mobile Hydraulic Power Units {7312}
C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Has Excessive Black Smoke
C175-16 Generator Set Engine Fuel Filter Housing - Remove and Install
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Vibration Is Excessive
C175-16 Generator Set Engine Fuel Control Valve - Remove and Install - Primary
2012/10/24 A New Water Temperature Regulator Is Available for Certain Commercial Engines {1355}
C175-16 Generator Set Engine Fuel Pump (High Pressure) - Remove and Install
C32 Marine Engines Cylinder Liner - Remove
2012/10/08 Check Valves Are Now Used in the Fuel System of Certain Electric Power Generation and Industrial Engines {1250, 1261, 5067}
C32 Marine Engines Cylinder Liner - Install
C32 Marine Engines Piston Cooling Jets - Remove and Install
C32 Marine Engines Inlet and Exhaust Valves - Remove and Install
C32 Marine Engines Pistons and Connecting Rods - Remove
C175-16 Generator Set Engine Air Cleaner - Remove and Install
C32 Marine Engines Pistons and Connecting Rods - Install
C32 Marine Engines Pistons and Connecting Rods - Disassemble