Water Temperature Regulator - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将冷却液从冷却系统中排入适当的容器至液位低于水温调节器,以便保存或废弃这些冷却液。 有关正确的排放步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 松开上部散热器软管上的软管卡箍,将上部散热器软管从水温调节器壳体 (2) 上断开。
Show/hide table
图 1 g01336665 典型示例 - 从水温调节器壳体 (2) 上卸下螺栓 (1)。
- 将水温调节器壳体 (2) 从缸盖上卸下。
注: 记录水温调节器壳体的朝向。
Show/hide table图 2 g01336667 典型示例 - 从水温调节器壳体 (2) 上卸下密封件 (3)。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 确保水温调节器壳体 (2) 的所有部件清洁且无磨损或损坏。
- 检查水温调节器是否正常工作。 请参阅系统操作、测试和调整, "水温调节器 - 测试",以了解测试水温调节器的步骤。 如果水温调节器的任何部件磨损或损坏,必须更换整个组件。
- 彻底清洁气缸的密封垫表面。
- 如果安装原来的水温调节器,将一个新 O 形密封圈 (3) 安置到水温调节器壳体 (2) 的凹槽中。
提供的新水温调节器壳体配有一个新 O 形密封圈。
- 将水温调节器壳体 (2) 安装到缸盖上。
注: 确保水温调节器壳体的朝向正确。
Show/hide table图 4 g01336665 典型示例 - 安装螺栓 (1)。 拧紧螺栓 (1) 至扭矩为
44 N·m (32 lb ft) 。 - 连接上部散热器软管,牢固地拧紧软管卡箍。
- 加注冷却系统至正确液位。 请参阅操作和保养手册, "冷却系统冷却液 - 检查"和操作和保养手册, "冷却系统冷却液 - 更换"以了解正确的加注步骤。
Show/hide table
图 3 | g01336667 |
典型示例 |
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Water Separator and Fuel Filter (Primary) - Remove and Install
C7.1 (Mech) Industrial Engine Water Pump - Remove
C7.1 (Mech) Industrial Engine Water Pump - Install
C7.1 (Mech) Industrial Engine Vibration Damper and Pulley - Remove
C7.1 (Mech) Industrial Engine Vibration Damper and Pulley - Install
C7.1 (Mech) Industrial Engine Valve Mechanism Cover - Remove and Install
C7.1 (Mech) Industrial Engine V-Belts - Remove and Install
C7.1 (Mech) Industrial Engine Turbocharger - Remove - Turbocharger Top Mounted
C7.1 (Mech) Industrial Engine Turbocharger - Remove - Side Mounted Turbocharger
C7.1 (Mech) Industrial Engine Turbocharger - Install - Side Mounted Turbocharger
C7.1 (Mech) Industrial Engine Turbocharger - Install - Side Mounted Turbocharger
C7.1 (Mech) Industrial Engine Rocker Shaft and Pushrod - Remove
C175-16 Marine Engine Engine Oil Screen
C175-16 Marine Propulsion Engines Fuel Pressure Is High - Fuel Transfer System
C175-16 Engines for Off-Highway Truck/Tractors Fuel Pressure Is Low - Fuel Transfer System
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is Low - Fuel Supply System
C175-16 Marine Propulsion Engines Fuel Pressure Is High - Fuel Supply System
C175-16 Marine Propulsion Engines Sensor Signal (Analog, Passive) - Test
2012/04/12 A New Service Replacement Front Housing Is Available for C175-16 Engines {1151, 1162, 1206}
C7.1 (Mech) Industrial Engine Air Compressor - Remove and Install
2012/02/20 New Torque Specification for Position Sensor on 3054E, C6.6, and C4.4 Engines {1408, 1907}
2012/06/08 Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
C175-16 Marine Engine Fuel and Auxiliary Water Pump Drive
C175-16 Marine Engine Vibration Damper