Engine Oil Pump - Disassemble
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Gp | 1 |
| B | 156-7100 | Slide Hammer Puller Gp | 1 |
Start By:
- Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove adapter (1) and the gasket.
Show/hide table
Illustration 2 g01005318 Show/hide table
Personal injury can result from parts and/or covers under spring pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
- Remove the bolts and cover (2). Remove gasket (3), spring (4), and valve spool (5).
Show/hide table
Illustration 3 g00591932 - Remove cover assembly (6) and the gasket.
Show/hide table
Illustration 4 g00591936 - Remove cover assembly (7).
Show/hide table
Illustration 5 g01050749 - Use Tooling (A) in order to remove bearings (8) from cover assembly (7).
Show/hide table
Illustration 6 g00591963 - Remove shaft assemblies (10) from body (9).
Show/hide table
Illustration 7 g01057505 - Use Tooling (A) in order to remove two of the three bearings (11) from body (9).
- Use Tooling (B) in order to remove the remaining bearing.
Show/hide table
| |
| Illustration 1 | g01005273 |
Caterpillar Information System:
3516C Locomotive Engines Engine Oil Pump - Install
CG137-08 and CG137-12 Industrial Engines Engine Control Panel
C15 Industrial Engines Refill Capacities
CG137-08 and CG137-12 Industrial Engines CAN Data Link - Test
C4.4 Industrial Engine Burn Prevention
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transfer Case Does Not Change Range
C4.4 Industrial Engine Maintenance Interval Schedule
CG137-08 and CG137-12 Industrial Engines Engine Oil Pressure - Test
CG137-08 and CG137-12 Industrial Engines Engine Stalls Immediately After Starting
CG137-08 and CG137-12 Industrial Engines Compression - Test
2011/02/15 A New Procedure is Now Used for Installing the Bearing Race in the Torque Converter Manifold for Certain CX Transmissions {3105}
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transfer Case Detent Switch
3516C Locomotive Engines Engine Oil Pump - Assemble
C4.4 Industrial Engine Radiator - Clean
2011/02/17 Replacing the Lock Assembly on Certain Generator Sets {7274}
2014/12/12 Proper Installation of Connecting Rod Bearings for G3600, 3600, and C280 Engines {1225}
C15 Industrial Engines Product Description
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure Hydraulic System
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Default Value of Work Tool Parameters
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Relief Valve (Line) - Test and Adjust
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control: Default Value of Work Tool Parameters
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Two-Way/One Pump - Electric Control: Default Value of Work Tool Parameters
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Two-Way/One Pump - Electric Control: Relief Valve (Line) - Test and Adjust
CG137-08 and CG137-12 Industrial Engines Engine Timing Does Not Match Programmed Timing