Engine Stalls Immediately After Starting
- 燃油供给
- 电气接头或电源
- 发动机速度/正时传感器
- 点火系统
- 负载过大
确认燃油压力正确。 如有可能,询问操作员以便确定燃料质量是否有问题。 试着确定燃料来源是否有所改变。
确保在稳定、充足的压力下供应燃料。 检查燃料管的尺寸是否大到足以为发动机提供充分体积的燃料。 检查燃料系统有无泄漏。
以下情况可能影响起动:
- 燃料压力低
- 燃料压力过高
- 燃油质量不良
检查以下燃料系统部件:
- 燃料滤清器
- 燃气压力调节器
- 燃气切断阀
- 燃料执行器
确认系统部件工作正常。
修理可疑部件。 必要时更换燃油滤清器。
- 检查电源连接和接地。 检查从电源至配电箱之间的导线线束和接头。 检查从配电盘到电子控制模块(ECM)的接线线束和接头。 请参阅测试与调整, "电气接头 - 检查"。
- 使用 Caterpillar 电子技师(ET)检查是否有激活的 168-2 电气系统电压不稳定、断续或不正确。 如果记录了此诊断代码,则转至故障诊断与排除, "电源 - 测试"。
确保发动机转速 / 正时传感器安装正确。 请参考故障诊断与排除, "转速/正时 - 测试"。
点火系统中的零件已经进行了显著改善,以便降低点火系统的损耗。 确保下列部件使用了最新零件:
- 主点火线束和接头
- 变压器
- 火花塞
检查点火系统有无以下情况:
- 检查点火变压器和火花塞之间的连接。 连接松动可能导致电弧放电和缺火。
- 确保发动机上安装了正确的变压器和火花塞。 检查火花塞有无结垢和湿气,间隙调节是否正确。
- 检查火花塞接线端有无腐蚀,检查电极有无磨损。 这两种情况都可能导致缺火。
其他损耗或缺火现象由短路或过多湿气导致。
按照操作和保养手册保养火花塞。
确保发动机上的负载没有过大。 降低负载。 如有必要,分离从动设备,然后再测试发动机。
Caterpillar Information System:
CG137-08 and CG137-12 Industrial Engines Compression - Test
2011/02/15 A New Procedure is Now Used for Installing the Bearing Race in the Torque Converter Manifold for Certain CX Transmissions {3105}
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transfer Case Detent Switch
XQP150 Rental Generator Set Fuel System Secondary Filter - Replace
XQP150 Rental Generator Set Fuel System Primary Filter (Water Separator) Element - Replace
CG137-08 and CG137-12 Industrial Engines Oil Filter Differential Pressure Problem
2011/02/08 New Product Link Cellular Is Released for All Cat Products {7606}
300.9D and 300.9D VPS Mini Hydraulic Excavator Electrical Storm Injury Prevention
349F and 352F Excavators Machine System Specifications Swing Motor
CG137-08 and CG137-12 Industrial Engines Intake Manifold Air Temperature Is High
CG137-08 and CG137-12 Industrial Engines Turbocharger Turbine Temperature Is High
CG137-08 and CG137-12 Industrial Engines Spark Plug - Test
CG137-08 and CG137-12 Industrial Engines Engine Oil Pressure - Test
C4.4 Industrial Engine Maintenance Interval Schedule
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transfer Case Does Not Change Range
C4.4 Industrial Engine Burn Prevention
CG137-08 and CG137-12 Industrial Engines CAN Data Link - Test
C15 Industrial Engines Refill Capacities
CG137-08 and CG137-12 Industrial Engines Engine Control Panel
3516C Locomotive Engines Engine Oil Pump - Install
3516C Locomotive Engines Engine Oil Pump - Disassemble
3516C Locomotive Engines Engine Oil Pump - Assemble
C4.4 Industrial Engine Radiator - Clean
2011/02/17 Replacing the Lock Assembly on Certain Generator Sets {7274}