UPSB220 Uninterruptible Power Supply Caterpillar


Measurement System

Usage:

UPSB 220 JFA



Illustration 1g02362618

Measurement System Diagram

(A) Rectifier/charger module

(B) Inverter module

(C) Static bypass module

(D) Battery unit

(1) Normal AC source

(2) Bypass AC source

(3) Battery

(4) Inverter output

(6) Total load

Illustration 1 provides an overview of the measurement system. Table 1 provides the description for the listed designators.

Table 1
Designator     Description    
U     Voltage    
V     Voltage (RMS)    
I     Current    
F     Frequency    
P     Power    

Using the Front Display

Available Measurements

The front display may be used to read the following input and output measurements made at different points in the system as indicated in Illustration 1.

(1) - Normal AC Source

  • Phase-to-phase voltages

  • Currents of the three phases

  • Frequency

(2) - Bypass AC Source

  • Phase-to-neutral voltage

  • Phase-to-phase voltages

  • Frequency

  • Currents of the three phases

(3) - Battery

  • Voltage

  • Charge or discharge current

  • Remaining battery time for the UPS or the affected unit

  • Battery temperature

(4) - Inverter output

  • Frequency

(6) - Total load

  • Phase-to-neutral voltage

  • Phase-to-phase voltages

  • Currents of the three voltages

  • Frequency

  • Active and apparent power

Accessing Measurements




Illustration 2g02365537

Front display panel

(13) "V" key

(14) "A" key

(15) "W.Hz" key

(20) Battery key

The keys listed below are located on the front control panel display shown in Illustration 2.

Voltage




Illustration 3g02362756

Voltage measurements

Note: M1 = Normal AC source and M2 = Bypass AC source

The measurements in Illustration 3 may be accessed by pressing the "V" key (13) .

Current




Illustration 4g02362757

Current measurements

Note: CF = Crest factor

The measurements in Illustration 4 may be accessed by pressing the "A" key (14) .

Power and Frequency




Illustration 5g02362759

Power and frequency measurements

Note: PF = Power Factor

The measurements in Illustration 5 may be accessed by pressing the "W.Hz" key (15) .

Battery




Illustration 6g02362758

Battery measurements

The measurements in Illustration 6 may be accessed by pressing the Battery key (20) .

Caterpillar Information System:

UPSB220 Uninterruptible Power Supply Logged Events
C-12 Engine Belts - Inspect/Adjust/Replace
C-12 Engine Belt Tensioner - Check
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Power Train Control Manifold (All Wheel Drive)
Reusability Recommendations for Duo-Cone Seals {7555, 7561} Reusability Recommendations for Duo-Cone Seals {7555, 7561}
2011/01/12 An Improved Procedure for Using an ECM for a Machine Test Is Now Available {7610}
Procedure to Use a Machine Electronic Control Module (ECM) for Machine Testing{7610} Procedure to Use a Machine Electronic Control Module (ECM) for Machine Testing{7610}
C-12 Engine Air Compressor - Check
C-12 Engine Configuration Parameters
2010/12/23 New Colors for the Injector Seals for C175-16 Generator Set Engines {1251, 1254, 1290, 1713, 7555}
C175 Generator Sets Engine Oil Sample - Obtain
C-12 Engine Plate Locations and Film Locations
UPSB220 Uninterruptible Power Supply Statistics
UPSB220 Uninterruptible Power Supply Time and Date Adjustment
2010/12/23 The Adapter for the High Pressure Fuel Rail Pressure Sensor Is Not Serviced for C175-16 Generator Set Engines {127A, 1718}
C15 and C18 Petroleum Generator Sets Coolant Temperature Regulator - Replace
C-12 Engine Engine Valve Lash - Check
C-12 Engine Fuel Injector - Inspect/Adjust
Installation of the Water-Cooled Throttle for G3500C and G3500E Generator Set Engines{1265} Installation of the Water-Cooled Throttle for G3500C and G3500E Generator Set Engines{1265}
2011/02/09 New Software is Now Used for C9 Industrial Engines {1901, 1902, 1920}
2010/12/20 Make Sure that the Radiator Fan for the 3500 Generator Set Engine Operates at the Correct Speed {1356, 1360}
C7 Engines for Combat and Tactical Vehicles Product Description
Idler Weld Rebuild Procedure {0679, 0729, 4150, 4159} Idler Weld Rebuild Procedure {0679, 0729, 4150, 4159}
C3.4B Engines for Caterpillar Built Machines Cleanliness of Fuel System Components
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.